vsp1500-irs.pdf

Specification

Reference

Sheet

VSP1500L

VSP1500R

Vehicle Specific Punch

Full Size GM Truck 1500 Extended Cab ’88+*

F EATURES

VSP E NCLOSURE

P UNCH W OOFER

• Vehicle Specific – The VSP1500L (left) and VSP1500R (right) are

custom molded to fit under the rear bench seat. The VSP1500R fits

without alteration, whereas the VSP1500L replaces the toolbox.

• PVA Cone – The cone material used is spruce pulp paper and provides

the necessary combination of weight and strength to allow high levels of

output without cone break up. The cone is also treated with a water resistant

PolyVinyl Acetate (PVA) Emulsion which increases cone rigidity and lowers

distortion.

• Aluminum Voice Coil Former – The voice coil is made of multiple

layers of copper wound on a black, anodized aluminum former. This

improves the speaker’s power handling by efficiently dissipating heat from

the voice coil.

• Acoustic Suspension Enclosure – The VSP enclosure uses an

acoustic suspension design (sealed) for optimum performance. The

enclosure is matched to the woofer for deep bass output while requiring

minimal operating space.

• Roto-Molded Urethane Construction – The use of Roto-Mold

manufacturing produces a composite enclosure with seamless construc-

tion. This greatly increases rigidity to prevent the enclosure from flexing

and allows custom designs to be fabricated. The result is a radical,

stronger, more reliable enclosure.

• Hyper-Extended Pole Piece – The pole piece has been extended to

provide a more linear magnetic field for the operation of the woofer. This

lowers distortion and provides the woofer with better low frequency

response.

• Vented Bumped Back Plate – The back plate has been stepped

deeper to allow the woofer more excursion for harder hitting bass.

Additionally, the back plate is vented with a radiused aerodynamic vent that

efficiently and quietly keeps the voice coil cool.

NOTE:

Use the VSP1500R for systems requiring only one subwoofer.

Use the VSP1500R and VSP1500L for systems requiring two

subwoofers.

S PECIFICATIONS

LE ....................................................................... 2.5mH

QMS ....................................................................... 4.08

QES ....................................................................... 0.27

QTS ........................................................................ 0.25

VAS (ft 3 /liter) .................................................. 2.72 (77L)

XMAX (in/mm) ............................................ 0.31” (8mm)

SPL (dB @ 1w/1m) ................................................. 87dB

Power Handling (RMS/Peak) ........................ 200W/400W

Speaker Displacement (ft 3 /liter) ................... 0.06 (1.699L)

VSP Enclosure

Frequency Response .............................................. 24Hz-400Hz

Overall Dimensions ea. .............................. 8”H x 30 1 ⁄ 2 ”W x 15”D

(20.32cm x 77.47cm x 38.10cm)

Weight ea. (woofer supplied) ....................... 22.6 lbs. (10.25kg)

Punch Woofer

Speaker Model .......................................................... RFP-1410

Nominal Impedance ............................................................. 4 W

............................................................................... 24Hz

............................................................................... 3.6 W

A CCESSORY P ACK

(1) Input Terminal Cup

(1) 3/8” – 16 x 1 1 ⁄ 4 ” Bolt

(1) 3/8” Lock Washer

(8) #10-32 x 3/4” Allen Screws

(4) Phillips Screws

(1) 3/8” ID x 1 1 ⁄ 2 ” OD Washer

(4) Foam Woofer Gaskets

(24”) Black/Red 16 gauge Speaker Wire

(1) 4” x 4” Wax Square (VSP1500R)

Specifications subject to change without notice

*For models without 3rd door option

–1–

VSP1500L

VSP1500R

Vehicle Specific Punch

Full Size GM Truck 1500 Extended Cab ’88+*

Installation

Reference

Sheet

The Vehicle Specific Punch (VSP) enclosure is supplied in kit form to allow custom finishing techniques. The unfinished surface

enables matching paint or carpet to be applied to the enclosure for seamless integration into the vehicle’s interior. In addition, the

input terminal cup can be positioned in the desired location where speaker wires can be conveniently routed from the amplifier to

the enclosure.

IMPORTANT – Please follow these instructions carefully!!

The VSP enclosure is specially molded to fit particular vehicles. Be sure to attach the enclosure to the vehicle as

specified in this installation sheet for optimized bass output. Failure to install the enclosure as specified in this docu-

ment may allow the enclosure to become detached from the vehicle and possibly cause personal injury.

Always use eye protection when drilling.

Never run wires underneath the vehicle. Run wires inside the vehicle and use rubber or plastic grommets

to protect wires routed through metal.

VSP ENCLOSURE PREPARATION

Select the desired location for the speaker terminal cup, and with a hole saw, cut a 2” diameter hole.

Using the speaker terminal cup as a template, mark the holes used to secure the cup to the enclosure.

Remove the cup and drill pilot holes using a 3/32” drill bit.

Carpet or paint the enclosure(s) to your desired color theme.

Connect the supplied speaker wire to the appropriate (+) and (–) terminals of the

speaker cup. Connect the RED wire to the (+) terminal and the BLACK wire to the (–)

terminal.

Secure the speaker terminal cup to the enclosure using the (4) supplied Phillips screws.

*For models without 3rd door option

–2–

VSP1500L

VSP1500R

Installation

Reference

Sheet

Vehicle Specific Punch

Full Size GM Truck 1500 Extended Cab ’88+*

VEHICLE PREPARATION

The VSP enclosure(s) will be located under the rear bench seat. Be sure to remove any

obstructions for proper installation.

Fold up the rear bench seat.

If installing the VSP1500L in addition to the VSP1500R, permanently remove the

factory toolbox located under the seat. Be sure to cover the extra hole using a rubber

plug or silicone sealant.

VSP 1500R ENCLOSURE INSTALLATION

Thread the supplied bolt fully into the VSP enclosure and test fit the enclosure in the

vehicle.

10. Remove the backing from the wax square and place it under the bolt location. Press

down firmly on the enclosure to make an impression of the bolt head into the wax

square. Making sure not to move the wax square, carefully remove the enclosure from

the vehicle.

11. Check under the vehicle for brake or hydraulic lines before proceeding. Using a 1/2”

diameter drill bit, drill a hole through the floor board using the wax square as your

template.

VSP 1500L ENCLOSURE INSTALLATION

12. If installing the VSP1500L in addition to the VSP1500R, test fit the enclosure in the

vehicle. Note that you will use the factory drilled tool box hole to secure the VSP1500L

to the vehicle.

13. Run the speaker wire from the amplifier to the desired location(s)

and connect the proper (+) and (–) speaker terminals to the

enclosure(s).

Enclosure Wall (urethane)

Threaded Insert

molded into enclosure

14. The next procedure will require 2 people. While one person is

positioning the VSP enclosure(s), the second person should insert the

long bolt(s) from the underside of the vehicle. Put a bead of silicone

sealant between the car sheet metal and the washer. Screw the bolt

into this threaded insert and tighten it. DO NOT OVERTIGHTEN.

Car’s sheet metal

Fender washer

Split lock washer

Bead of Silicone Sealant

15. After the bolt(s) are tightened, spray rubberized undercoating over the

bolt(s) and over any bare metal. This will prevent the metal from

rusting and will prevent the bolt(s) from loosening due to vibrations.

3/8” bolt

16. If necessary, fine tune the system to find the proper bass level for your new VSP woofer enclosure.

VSP1500L & VSP1500R

VSP1500R

*For models without 3rd door option

–3–

L IMITED W ARRANTY I NFORMATION

Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms:

•

Length of Warranty

1 year on VSP speakers (not the entire enclosure)

•

What is Covered

This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States

of America or its possessions. Product purchased by consumers from an Authorized Rockford Fosgate Dealer in another country are covered

only by that country’s Distributor and not by Rockford Corporation.

•

Who is Covered

This warranty covers only the original purchaser of Rockford product purchased from an Authorized Rockford Fosgate Dealer in the United

States. In order to receive service, the purchaser must provide Rockford with a copy of the receipt stating the customer name, dealer name,

product purchased and date of purchase.

•

Products found to be defective during the warranty period will be repaired or replaced (with a product deemed to be equivalent) at

Rockford's discretion.

•

What is Not Covered

1. Damage caused by accident, abuse, improper operations, water, theft

2. Any cost or expense related to the removal or reinstallation of product

3. Service performed by anyone other than Rockford or an Authorized Rockford Fosgate Service Center

4. Any product which has had the serial number defaced, altered, or removed

5. Subsequent damage to other components

6. Any product purchased outside the U.S.

7. Any product not purchased from an Authorized Rockford Fosgate Dealer

•

Limit on Implied Warranties

Any implied warranties including warranties of fitness for use and merchantability are limited in duration to the period of the express warranty

set forth above. Some states do not allow limitations on the length of an implied warranty, so this limitation may not apply. No person is

authorized to assume for Rockford Fosgate any other liability in connection with the sale of the product.

•

How to Obtain Service

Please call 1-800-669-9899 for Rockford Customer Service. You must obtain an RA# (Return Authorization number) to return any product

to Rockford Fosgate. You are responsible for shipment of product to Rockford.

Ship to: Speakers

Rockford Acoustic Design

(Receiving-speakers)

609 Myrtle N.W.

Grand Rapids, MI 49504

RA#:_________________

Ship to: Electronics

Rockford Corporation

Warranty Repair Department

2055 E. 5th Street

Tempe, AZ 85281

RA#:_________________

MADE IN THE USA

This product is designed, developed and assembled in the USA by a dedicated group of American

workers. The majority of the components used in the construction of this product are produced by

American companies. However, due to the global nature of their manufacturing facilities and the

electronics parts industry in general, some parts may be manufactured in other countries.

Rockford Fosgate

Rockford Corporation

546 South Rockford Drive

Tempe, Arizona 85281 U.S.A.

In U.S.A., (602) 967-3565

In Europe, Fax (49) 850-3934-014

In Japan, Fax (81) 559-79-1265

www.rockfordfosgate.com

LIT10028

4/98

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: