el_sarex_07_16_en.pdf

(107 KB) Pobierz
79.0
List of spare parts
S2
S2
S2
SAEx 16.1
SAREx 16.1
50.1
SAEx 07.1 – SAEx 16.1
SAREx 07.1 – SAREx 16.1
50.020
50.021
50.023
50.042
S1/S2
79.0
160.2
S2
SAEx 07.1 – SAEx 14.1
SAREx 07.1 – SAREx 14.1
S2
50.016
50.2
160.1
152.2
153.2
70.0
151.0
27
S1/S2
S1/S2
39
152.1
51.16
153.1
155.0
S1/S2
153.3
S1/S2
20.0
153.0
S2
59.0
24
5.7
5.0
25.0
019
020
24.0 / 23.0
22.0
19.0
S2
5.12
153.5
17.0
70.1
5.8
9.0
49.0
5.37
30.0
S2
5.32
10.0
S2
053
S2
18
105.0
1.0
012
6
S1/S2
3.0
14
80.001
107
156.0
60.0
80.0
100
90.001
106.0
80.3
S2
S2
61.0
85.001
80.001
90.0
85.0
2.0
15.0
85.001
1.03
Y000.208/002/en
S2
90.001
B1/C
A
D
B3/B4/E
802736020.016.png 802736020.017.png 802736020.018.png 802736020.019.png 802736020.001.png 802736020.002.png 802736020.003.png 802736020.004.png 802736020.005.png 802736020.006.png 802736020.007.png 802736020.008.png 802736020.009.png
 
SAEx 07.1 – SAEx 16.1
SAREx 07.1 – SAREx 16.1
List of spare parts
When placing orders for spare parts, it is essential to mention type of actuator and our commission number
(refer to name plate).
No.
Type
Designation
No.
Type
Designation
012
E
Notched pin
50.042
E
Insulation plate
019
E
Cheese head screw
51.16
B
Frame-extension assly.
020
E
Clamping washer
59.0 1)
B
Pin for motor and thermoswitch in motor plug
053
E
Countersunk screw
Control unit assly. (but without torque head,
without switches)
60.0
B
1.0
B
Housing assly.
2.0
B
Flange, bottom assly.
61.0
B
Torque switching head
3.0
B
Hollow shaft assly. (without worm wheel)
70.0
B
Motor
5.0
B
Worm shaft assly.
70.1 1)
B
Motor pin carrier (without pins)
5.7
E
Motor coupling
79.0 2)
B
Planetary gearing for motor drive assly.
5.8
B
Manual drive coupling assly.
Output drive Form A assly. (without thread
in stem nut)
80.0
B
5.12
E
Grub screw
5.32
E
Coupling pin
80.001 3)
E
Thrust bearing set
5.37
B
Pull rod assly.
80.3 3)
E
Stem nut Form A (without thread)
6
E
Worm wheel
85.0 3)
B
Output drive B3
9.0
B
Planetary gear for manual drive assly.
85.001 3)
E
Snap ring
10.0
B
Retaining flange assly.
90.0 3)
B
Output drive D
14
E
Change-over lever
90.001 3)
E
Snap ring
15.0
B
Cover for switch compartment assly.
Switch for limit / torque switching
(including wire end sleeves)
100
B
17.0
B
Torque lever assly.
18
E
Gear segment
Blinker transmitter including wire end sleeves
(without impulse disc and insulation plate)
105.0 3)
B
19.0
B
Crown wheel assly.
20.0
B
Swing lever assly.
106.0
B
Stud bolt for switches
22.0
B
Drive pinion II for torque switching assly.
107
E
Spacer
23.0
B
Drive wheel for limit switching assly.
151.0
B
Space heater
24
E
Drive wheel for limit switching
152.1 3)
B
Potentiometer (without slip clutch)
24.0
B
Intermediate wheel for limit switching assly.
152.2 3)
B
Slip clutch for potentiometer
25.0
E
Locking plate
153.0 3)
B
RWG assly.
27
E
Screw plug
153.1 3)
B
Potentiometer for RWG (without slip clutch)
30.0
B
Handwheel with ball handle assly.
153.2 3)
B
Slip clutch for RWG
39
E
Screw plug
153.3 3)
B
Electronic board RWG
49.0 1)
B
Motor plug, socket assly.
153.5 3)
B
Wires for RWG
50.1
B
Cover assly.
155.0 3)
B
Reduction gearing
156.0 3)
B
Mechanical position indicator
Terminal carrier-frame assly.
(without terminals)
50.2
B
160.1 3)
E
Protection tube (without cap)
50.016
E
End-piece
160.2 3)
E
Cap for stem protection tube
50.020
E
Terminal
S1
S
Seal-kit, small
50.021
E
Terminal
S2
S
Seal-kit, large
50.023
E
Terminal plate
When performing maintenance or repairs on the actuators, the requirements of the EN 60079-17, as well as the notes in the
operation instructions must be strictly observed.
Type B = Sub-assembly
Type E = Component
Type S = Set
assly. = assembly
1)
SAEx 16.1 with output speeds 32 to 180 1/min or SAREx 16.1 with output speeds 32 and 45 1/min without motor
plug/socket assly; motor directly wired to terminals (no. 50.020).
2)
only required for some output speeds
3)
optional extra, not included in basic equipment
1.03
Issue
Y000.208/002/en
802736020.010.png 802736020.011.png 802736020.012.png 802736020.013.png 802736020.014.png 802736020.015.png
 
Zgłoś jeśli naruszono regulamin