SONY.DSLR-A700.LEVEL2.VER1.2.pdf

DSLR-A700

RMT-DSLR1

SERVICE MANUAL

LEVEL 2

US Model

Canadian Model

AEP Model

UK Model

E Model

Australian Model

Hong Kong Model

Chinese Model

Korea Model

Japanese Model

Ver. 1.2 2008.02

Revision History

Revised-1

Replace the previously issued

SERVICE MANUAL 9-852-212-31

with this manual.

Link

SPECIFICATIONS

BLOCK DIAGRAMS

PRINTED WIRING BOARDS

SERVICE NOTE

FRAME SCHEMATIC DIAGRAMS

REPAIR PARTS LIST

DISASSEMBLY

SCHEMATIC DIAGRAMS

The components identified by

mark 0 or dotted line with

mark 0 are critical for safety.

Replace only with part num-

ber specified.

Les composants identifiés par une

marque 0 sont critiques pour la

sécurité.

Ne les remplacer que par une pièce

portant le numéro spécifié.

DIGITAL SINGLE LENS REFLEX CAMERA

DSLR-A700_L2

2008B0500-1

Published by Kohda TEC

9-852-212-32

Sony EMCS Co.

Link

SPECIFICATIONS

Camera

[System]

Camera Type

Digital Single Lens Reflex

Camera with built-in flash and

interchangeable lenses

[Exposure]

Metering Cell 40-segment honeycomb-pattern

SPC

Metering Range 0 EV to 20 EV (+2 EV to +20

EV with Spot metering), (at

ISO 100 with F1.4 lens)

[Others]

PictBridge Compatible

Exif Print Compatible

PRINT Image Matching III

Compatible

Image format

23.5×15.6mm (APS-C format)

Exif

Exif Ver.2.21

[Shutter]

Type

Lens

All of Sony Lens

RAW

ARW2.0 format

Electronically-controlled,

vertical-traverse, focal-plane

type

[Image sensor]

Total pixel number of camera

Approx. 13 053 000 pixels

Effective pixel number of camera

Approx. 12 246 000 pixels

[Super SteadyShot]

System Image sensor-Shift mechanism

Super SteadyShot Compensation capability

Approximately 2.5 EV to 4 EV

decrease in shutter speed

(varies according to shooting

conditions and lens used)

79.7mm (55/8 × 4 1 /4 ×

31/4 inches) (W/H/D,

excluding protrusions)

Mass Approx.690 g (1 lb 8.3 oz)

(without batteries, memory card

and body accessories)

Operating temperature

0 to 40

Approx. 141.7

104.8

Speed range

1/8000 second to 30 seconds,

bulb

Flash Sync Speed

1/250 second (with Super

SteadyShot off),

1/200 second (with Super

SteadyShot on)

(When using the Microdrive: 5

to 40

C (32 to 104

[Built-In-Flash]

Flash G.No. GN 12 (in meters at ISO 100)

Recycling Time Approx. 3 seconds

[Recording media]

CompactFlash card(TypeI,II),

Microdrive, “Memory Stick

Duo”

C (41 to 104

F))

BC-VM10 Battery charger

Input rating 100 V – 240 V AC, 50/60 Hz

Output rating 8.4 V DC, 750 mA

Operating temperature range

0 to 40°C (32 to 104°F)

Storage temperature range

–20 to +60

[Anti-Dust]

System

Charge protection coating on

Low-Pass Filter and image

sensor-Shift mechanism

[Viewfinder]

Type Fixed eye-level system with

optical glass type pentaprism

Focusing Screen Spherical Acute Matte

Field of View

[LCD monitor]

LCD panel 7.5 cm (3.0 type) TFT drive

Total number of dots

921 600 (640

C (–4 to +140

Maximum dimensions

Approx. 70 × 25 × 95 mm

(2 7/8

3 3/4 inches) (W/H/

3 (RGB)

480)

Mass Approx. 90 g (3.2 oz)

Rechargeable battery pack NP-FM500H

Used battery Lithium-ion battery

Maximum voltage

DC 8.4 V

Nominal voltage DC 7.2 V

Maximum charge current

2.0 A

Maximum charge voltage

DC 8.4 V

Capacity 11.8 Wh (1 650 mAh)

Maximum dimensions

Approx. 38.2 × 20.5 × 55.6 mm

(1 9/16

0.95

dots

[Input/output terminals]

VIDEO OUT terminal

Special multi-connector

USB terminal Special multi-connector, Hi-

speed USB (USB 2.0

compliant)

HDMI OUT terminal

HDMI type C minijack

with 50mm lens at

infinity, –1 m –1

Eye Relief Approximately 25 mm from the

eyepiece, 21 mm from the

eyepiece frame at –1 diopter

(–1m –1 )

Dioptor Adjustment

–3.0 to +1.0 m –1

[Auto Focus System]

System

0.9

TTL phase-detection system,

CCD line sensors (Metering

area 11 points)

Sync. terminal

REMOTE terminal

[Power, general]

Used battery pack

Sensitivity Range

Rechargeable battery pack

NP-FM500H

0 EV to +18 EV (at ISO 100

equivalent)

13/16

2 1/4 inches)

(W/H/D)

Mass

Approx. 78 g (2.8 oz)

Design and specifications are subject to change

without notice.

DSLR-A700_L2

— 2 —

Dimensions

Magnification

1. SERVICE NOTE

ENGLISH

JAPANESE

1-1. CHEMICALS

Some chemicals used for servicing are highly volatile.

Their evaporation caused by improper management affects your health and environment, and wastes resources.

Manage the chemicals carefully as follows.

• Store chemicals sealed in a specific place to prevent from exposure to high temperature or direct sunlight.

•Aoid dividing chemicals into excessive numbers of small containers to reduce natural evaporation.

•Keep containers sealed to avoid natural evaporation when chemicals are not in use.

•Aoid using chemicals as much as possible. When using chemicals, divide only required amount to a small plate from the container and

use up it.

1-2. EXTERIOR PARTS

Be careful to the following points for plastic parts used in this unit.

• Use a piece of cleaning paper or cleaning cloth for cleaning plastic parts. Avoid using chemicals.

Even if you have to use chemicals to clean heavy dirt, don’t use paint thinner, ketone, nor alcohol.

• Insert the specific screws vertically to the part when installing a plastic part.

Be careful not to tighten screws too much.

1-3. UNLEADED SOLDER

This unit uses unleaded solder.

Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead.

( Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)

: LEAD FREE MARK

Be careful to the following points to solder or unsolder.

• Set the soldering iron tip temperature to 350 °C approximately.

If cannot control temperature, solder/unsolder at high temperature for a short time.

Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!

Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur

such as on IC pins, etc.

• Be sure to control soldering iron tips used for unleaded solder and those for leaded solder so they are managed separately. Mixing

unleaded solder and leaded solder will cause detachment phenomenon.

1-4. SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and

bridges.

2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the

customer and recommend their replacement.

4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their

replacement.

5. Check the B+ voltage to see it is at the values specified.

6. Flexible Circuit Board Repairing

•Keep the temperature of the soldering iron around 270 °C during repairing.

• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering or unsoldering.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

SAFETY-RELATED COMPONENT WARNING!!

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES

DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT

CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE

REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY

DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU

DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH

MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS

LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE

COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS

APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS

PUBLISHED BY SONY.

DSLR-A700_L2

1-1

ENGLISH

JAPANESE

Ver. 1.1 2007.10

The changed portions from

Ver. 1.0 are shown in blue.

ENGLISH

JAPANESE

1-5. METHOD OF EXCHANGING SI SCREEN AND FOCUSING SCREEN

The focusing screen of the DSLR-A700 is available with two types,

standard and M type.

If the type was changed due to the replacement of focusing screen,

the setting must be changed according to the type.

Adjusting Item: “Focusing Screen Type Select”

1 Remove two claws pushing part A below,

and remove focus plate retainer (SP) in the

direction of arrow.

3 Remove focusing screen and VB washer.

VB Washer

Claw

Focusing Screen

Focus Plate Retainer (SP)

2 Remove focus plate retainer (SP).

Focus Plate Retainer (SP)

4 Remove SI screen.

SI Screen

Claw

Note: When you exchange the SI screen,

don't put dust or give a scratch.

DSLR-A700_L2

1-2

ENGLISH

JAPANESE

1. SERVICE NOTE

ENGLISH

JAPANESE

֤छༀ඼ͷऔΓѻ͍ʹ͍ͭͯ

ݱࡏ࢖༻͞Ε͍ͯΔༀ඼ͷதʹ͸شൃੑͷߴ͍ༀ඼΋͋Γ·͢ɻ

ͦΕΒΛෆ༻ҙʹऔΓѻ͍ৠൃͤͯ͞͠·͏ͱɼ؀ڥ΍݈߁΁ӨڹΛ༩͑ͨΓɼࢿݯͷແବ࢖͍ʹͳΓ·͢ɻ

֤छༀ඼͸ɼԼهͷ఺ʹ஫ҙͯ͠औΓѻ͍ͬͯͩ͘͞ɻ

ɾ อ؅৔ॴΛఆΊɼߴԹʹͳͬͨΓ௚ࣹ೔ޫͷ౰ͨΒͳ͍৔ॴʹີดͯ͠อ؅͍ͯͩ͘͠͞ɻ

ɾ খ෼͚ʢϋϯυϥοϓ౳ʣ͢Δ਺͸ඞཁ࠷খݶʹཹΊɼ༰ثʹΑΔࣗવৠൃΛ๷͍Ͱ͍ͩ͘͞ɻ

ɾ ࡞ۀʹ࢖༻͠ͳ͍࣌͸ɼඞͣΩϟοϓ౳Λͯࣗ͠વৠൃΛ๷͍Ͱ͍ͩ͘͞ɻ

ɾ ༀ඼Λ࢖༻͢Δճ਺Λۃྗগͳ͘͠ɼ࢖༻͢Δ৔߹͸࢖༻͢Δྔ͚ͩ༰ثΑΓग़ͯ͠ड͚ࡼʹ࢒͞ͳ͍Α͏ʹͯͩ͘͠

͍͞ɻ

थࢷܥ෦඼ͷऔΓѻ͍ʹ͍ͭͯ

ຊػʹ࢖༻͞Ε͍ͯΔथࢷܥͷ෦඼͸ɼԼهͷ఺ʹ஫ҙͯ͠औΓѻ͍ͬͯͩ͘͞ɻ

ɾ ਗ਼૟ʹ͸ༀ඼Λ࢖༻ͤͣɼਗ਼૟ࢴ΍ਗ਼૟෍Λ࢖༻͍ͯͩ͘͠͞ɻ

΍ΉΛಘͣԚΕ͕ͻͲͯ͘ༀ඼Λ࢖༻͢Δ৔߹͸ɼγϯφʔɼέτϯɼΤʔςϧ͸࢖༻͠ͳ͍Ͱ͍ͩ͘͞ɻ

ɾ ֤෦඼ͷऔΓ෇͚ʹ͸ࢦఆ͞ΕͨͶ͡Λ࢖༻͠ɼ෦඼ʹରͯ͠ਨ௚ʹऔΓ෇͚͍ͯͩ͘͞ɻ

·ͨɼͶ͡ΛకΊ෇͚Δ࣌͸ɼແཧͳྗΛՃ͑ͳ͍Ͱ͍ͩ͘͞ɻ

ແԖ൒ాʹ͍ͭͯ

ຊػʹ͸ແԖ൒ా͕࢖༻͞Ε͍ͯ·͢ɻ

ແԖ൒ాΛ࢖༻͍ͯ͠Δج൘ʹ͸ɼແԖʢ-FBE'SFFʣΛҙຯ͢ΔϨουϑϦʔϚʔΫ͕ϓϦϯτ͞Ε͍ͯ·͢ɻ

ʢ ஫ҙɿ ج൘αΠζʹΑͬͯ͸ɼແԖ൒ాΛ࢖༻͍ͯͯ͠΋ϨουϑϦʔϚʔΫ͕ϓϦϯτ͞Ε͍ͯͳ͍΋ͷ͕͋Γ·͢ʣ

ɿϨουϑϦʔϚʔΫ

ແԖ൒ా͸ɼԼهͷ఺ʹ஫ҙͯ͠࢖༻͍ͯͩ͘͠͞ɻ

ɾ ൒ాͯ͜ͷͯ͜ઌԹ౓͸໿ˆʹઃఆ͍ͯͩ͘͠͞ɻ

Թ౓ௐઅ͕ແཧͳ৔߹͸ɼߴԹ୹࣌ؒͰ࡞ۀΛߦ͍ͬͯͩ͘͞ɻ

஫ҙɿ ൒ాͯ͜Λ௕͘౰ͯ͗͢Δͱɼج൘ͷύλʔϯʢಔഩʣ͕͸͕Εͯ͠·͏͜ͱ͕͋Γ·͢ͷͰɼ஫ҙͯͩ͘͠͞

͍ɻ·ͨɼैདྷͷ൒ాΑΓ΋೪ੑ͕ڧ͍ͨΊɼ*$୺ࢠͳͲ͕൒ాϒϦοδ͠ͳ͍Α͏ʹ஫ҙ͍ͯͩ͘͠͞ɻ

ɾ ൒ాͯ͜ͷͯ͜ઌ͸ɼඞͣແԖ൒ా༻ͱ༗Ԗ൒ా༻ʹ෼͚ͯ؅ཧ͍ͯͩ͘͠͞ɻ

ແԖ൒ాͱ༗Ԗ൒ా͕ࠞࡏ͢Δͱണ཭ݱ৅͕ൃੜͯ͠͠·͍·͢ɻ

DSLR-A700_L2

1-3

ENGLISH

JAPANESE

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: