Arbor & sun shade.pdf

(148 KB) Pobierz
B u i l d t h e W i n d s o r s h a d e s h e l t e r
B u i l d t h e W i n d s o r s h a d e s h e l t e r
This handsome, freestanding redwood shade shelter will provide a cool
place to relax in the garden or yard. The shelter can also be built next to
your home where it will keep the whole house cooler by shielding windows,
walls and glass doors from the sun.
Redwood grades especially suited for this and other outdoor garden projects
are Construction Common and Deck Common. Use the all-heartwood
grades, Construction Heart or Deck Heart, where a greater degree of decay
resistance is needed.
A simple weekend project, this shelter will shade an area of approximately 8
feet by 12 feet or 96 square feet. The basic plan can be modified by adding
more posts, longer beams and additional louvers. If you decide to enlarge
this project, keep in mind that the rafters should span no more than 6 feet.
Before beginning any home remodelling project, check with your local
building department to learn if a permit is required and to discover any
special building codes for your locality. Use only non-corrosive hardware
and fasteners to prevent staining. If you plan to paint your shelter, it will be
easier if you prime all edges, ends and sides before constructing the shelter.
The first step is to place and prepare the footings...
108270661.026.png
P r e p a r e
t h e f o o t i n g s
Prepare footings for the 4x4 posts that are spaced 6 feet o.c. and 9 feet o.c.
The type of footing for posts will vary depending on the deck, patio or type
of bare ground the shelter covers. In all cases, the posts should be heartwood
grade redwood. Check local building codes for footing requirements in your
area. Use quick-setting concrete that hardens in about an hour.
108270661.027.png 108270661.028.png 108270661.029.png 108270661.001.png 108270661.002.png 108270661.003.png
A t t a c h
t h e p o s t s
Install or attach a 10- to 12-foot-long 4x4 post in each footing. Use a
carpenter’s level and temporary cross bracing—from the ground to the
post—to keep the post plumb. Trim posts to final
height if necessary. Posts should measure 8 feet high from the surface of the
ground, patio or deck. Remove the temporary bracing once the beams and
rafters are installed.
108270661.004.png 108270661.005.png
I n s t a l l
t h e b e a m s
Two 12-foot-long 2x6 beams are attached to each set of posts, one on each
side and extending 18 inches outward from the centre line of the posts. Nail
or screw the beams to position them even with the tops of the posts. Drill
two 1 /2" diameter holes through the double beams and posts. Secure with
two 7-inch machine bolts.
108270661.006.png 108270661.007.png 108270661.008.png 108270661.009.png
C u t a n d a t t a c h
t h e b r a c e s
Cut the remaining 4x4s into four pieces, each 30 inches long and with a 45-
degree angle on each end. Fasten the bottom of each brace with a 6-inch
machine bolt and countersink the washer and nut. The top of the brace is
sandwiched between the double beams and secured with a 7-inch machine
bolt.
108270661.010.png 108270661.011.png 108270661.012.png 108270661.013.png 108270661.014.png 108270661.015.png 108270661.016.png 108270661.017.png 108270661.018.png 108270661.019.png 108270661.020.png 108270661.021.png 108270661.022.png 108270661.023.png 108270661.024.png 108270661.025.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin