WHIPPET.pdf

(234 KB) Pobierz

WHIPPET_PARTS_V2.cdr

6a

7R

8

4

2

3

7L

1

5

6b

9

3

Cm

311456350.051.png

311456350.062.png

311456350.065.png

Paperpanzer.co.uk

Medium tank A “Whippet”

Printing Instructions

This model has been designed to be printed on an A4 sheet of 120 – 160gsm card.

Tools Needed

Scissors or Sharp Model Knife

PVA Glue

Ruler

Model Construction

Cut Line

Ridge Fold Line

Valley Fold Line

Attached Parts Outline

1,

Cut out the hull (part 1), score

along dotted lines and form the

main body and glue, then fold in

and glue the sides.

2,

Cut out the upper body (part 2),

score along dotted lines and glue

together. Once dry attach it to the

main body.

Note: the front of the upper body

needs to be flush with the front of

the hull in order to fit on the

engines

311456350.066.png

311456350.001.png

311456350.002.png

311456350.003.png

311456350.004.png

311456350.005.png

311456350.006.png

311456350.007.png

311456350.008.png

311456350.009.png

311456350.010.png

311456350.011.png

311456350.012.png

311456350.013.png

311456350.014.png

311456350.015.png

311456350.016.png

311456350.017.png

311456350.018.png

Paperpanzer.co.uk

Medium tank A “Whippet”

3,

Cut out the crew compartment

(part 3), score along dotted lines.

The crew compartment folds

together in four directions.

a,

The right side folds around full

circle to form a “D”.

b,

The left side folds in.

c,

The roof of the crew compartment

splits into two, the right-hand side

covers the “D”. The left-hand side

is formed around the crew

compartment.

d,

There is a floor to the crew

compartment that folds underneath

(not seen in picture)

4,

Once complete the crew

compartment can be attached to

the upper body.

NOTE: There is an overhang on the right-

hand side so that the floor of the

crew compartment should fit over

the upper body.

5,

Cut out the engines (part 4) and

score along the dotted lines. To

the rear of the engines there is a

slight over-hang (where the engine

access doors should be)

Once dry the fuel tank (part 5) can

be cut out formed and attached to

the front of the engines.

311456350.019.png

311456350.020.png

311456350.021.png

311456350.022.png

311456350.023.png

311456350.024.png

311456350.025.png

311456350.026.png

311456350.027.png

311456350.028.png

311456350.029.png

311456350.030.png

311456350.031.png

311456350.032.png

311456350.033.png

311456350.034.png

311456350.035.png

311456350.036.png

311456350.037.png

311456350.038.png

311456350.039.png

311456350.040.png

Paperpanzer.co.uk

Medium tank A “Whippet”

6,

Parts 7L & 7R are the track

sponsons, 6a & 6b are to be glued

inside of the sponsons to give them

some strength. The tracks (part 8)

then wrap around the sponsons,

the tracks are slightly wider so

there will be a little overhang on

either side.

7,

Attach the sponsons either side of

the hull

8,

Finally the machine guns x4 (part

9), roughly cut out first then fold

and glue before cutting to shape.

Attach each machine gun in the

centre of the ball mount.

Finished

311456350.041.png

311456350.042.png

311456350.043.png

311456350.044.png

311456350.045.png

311456350.046.png

311456350.047.png

311456350.048.png

311456350.049.png

311456350.050.png

311456350.052.png

311456350.053.png

311456350.054.png

311456350.055.png

311456350.056.png

311456350.057.png

311456350.058.png

311456350.059.png

311456350.060.png

311456350.061.png

311456350.063.png

311456350.064.png

Plik z chomika:

Inne pliki z tego folderu:

Schneider CA1.pdf (392 KB)
A7V.pdf (156 KB)
WHIPPET.pdf (234 KB)
Ford T.pdf (4303 KB)
kaiser_bussing.pdf (1851 KB)

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin