Zoe dress instructions(1).pdf

(269 KB) Pobierz
Microsoft Word - Zoe8123B .doc
Copy Paper with DinA4 Print:
The pattern pieces are printed with a narrow border onto 24 pages. Wait until all pages are printed. Arrange
the pages as depicted in the page with instructions on how to put the pages together.
Cut the pages at the upper right edge along the narrow border. Start with the lower left page and glue the
pieces together at the border lines.
Choose the size of the patter according to the Burda measurement chart. The sizes for dresses, Blouses,
Jackets and Coats are determined by the bust measurement, the sizes for pants and skirts are determined by
the hip measurement.
Adjust, if necessary, if your measurements differ from the Burda measurement chart.
Cut the pattern pieces for your size.
Lengthening or Shortening the Pattern
Our cut is designed for a height of 168 cm. (5 feet 5 inches). If you are taller or shorter, you can adjust the
pattern at the lines that say, “shorten or lengthen here”. That way, the fit remains the same.
⇒Always change all pattern pieces at the same line and the same length.
How to:
Cut the pattern lines at the marked lines.
To lengthen: Push the pieces apart as far as necessary.
To shorten: Push the pieces together as far as necessary.
Adjust the side edges.
1
194664749.007.png 194664749.008.png 194664749.009.png 194664749.010.png
Cutting out
Selvage (-----) means : This is the middle of a pattern pieces, not an edge or a seam. The piece is cut twice
the size of the pattern; the selvage is the middle axis of the piece.
The pattern pieces with interrupted outlines are placed onto the fabric with the printed side facing down.
The cutting plans show how to arrange the pattern pieces on the fabric.
If fabric is not folded , pin the pattern pieces to the right side.
If fabric is folded , pin the pattern pieces with the right side of the fabric facing inside. Pin pattern pieces
on wrong side.
Place cutting plan over the selvage, finally, cut with fabric not folded.
Seam and Hem Allowances are included in the pattern:
4 cm (1 ½ inches) Seam and 1.5 cm ( 1/2 inch ) at all other edges and seams.
Cut Fabric Folded:
Fold the fabric in half lengthwise ; the right side is facing inside. The selvage lines
Are facing each other. Pin pattern piece 1, as depicted in the copy paper, onto the wrong side of the fabric.
Cut pattern pieces.
Sometimes it is necessary to fold the fabric’s edges toward the selvage. This way, you get two selvages, to
which you can pin skirt pieces and the front facing.
Marking
Before you remove the pattern pieces from the fabric, please draw all important markings and lines on the
pattern pieces, for example the selvage lines and the horizontal lines. This is easiest using Burda tracing
paper and a tracing wheel (see instructions in package) or using pins and tailor’s chalk. Transfer the wrap
lines with batching stitches onto the right side of the fabric.
Interfacing
Cut interfacing according to drawing on left and iron onto the wrong side of the fabric.
Sewing
When sewing, the right sides of the fabric are facing.
2
194664749.001.png 194664749.002.png
Dress
Darts
1.) Pin chest darts at the front piece and stitch
ending in a narrow tip. Tie thread. Iron
darts toward bottom.
2.) Pin waist darts of the back pieces and
stitch ending in a narrow tip. Tie thread.
Iron darts toward middle.
Back Middle Seam
3.) Place back pieces right sides facing, pin
middle seam, stitch coming from the slit
marking (arrow) going downward. Secure
seam ends. Leave slit pinned. Trim seam
allowances, fold apart and iron.
Zip
4.) Pin zip underneath the slit edges so that the
teeth are covered. Stitch zip onto garment
with zipper foot. Sizes 36-44: Let zip end
overlap at bottom.
Front Skirt Piece/ Inverted Pleat
5.) Fold front skirt piece in half, right sides
facing. Pin pleat lines (front middle) onto
another.
6.) Iron pleat so that the lines that are pinned
onto each other hit the middle. Pin pleat to
the upper edge.
Loops
7.) Fold loops at selvage lines, right side
inside. Stitch edges onto another, trim
seam allowances. Turn loops. Pin edges,
iron and stitch neatly. De-baste upper
edges.
8.) Stitch loops right sides facing onto the
upper side of the marked lines of the front
and back piece. Secure seam ands. Place
loops downward, pin.
3
194664749.003.png 194664749.004.png
4
Pin Skirt Pieces
9.) Pin front skirt piece onto front bodice
piece right sides facing (seam number 1)
and stitch. Trim seam allowances, de-
baste held together and iron into the
front piece.
Stitch back skirt piece onto back piece in the
same way.
Side seams
10.) Place front piece right sides facing onto
the back piece, pin side seams (seam
number 3), skirt base seams meet. Stitch.
Trim seam allowances, fold apart and
iron.
Seam: Tear basting stitches at pleat
11.) De-baste seam, fold over, iron. Stitch
seam by hand loosely. Iron in pleat at
seam.
Neckline/ Facing
12.) Place back facings onto front facings
right sides facing, stitch side seams
(seam number 5)_
⇒Fold over the seam allowances of the
shoulder edges and iron to inside.
13.) Pin facing onto the dress, right sides
facing, side seams meet. Fold over the
back facing’s edges at the zip. Pin and
stitch the facing to the neckline and arm
line edges and stitch. Trim seam
allowances. Cut in.
Shoulder Seams
14.) Place front pieces onto back piece right
sides facing, stitch shoulder seams (seam
number 4), holding in the backwards
shoulder edges. Cut the seam allowances
diagonally at edges. Pull seam
allowances towards inside, fold apart
and iron.
15.) Sew the facing edges at the shoulders
against each other by hand. Pin all
necklines, iron and stitch neatly. Sew
back facing edges onto the zipper bands.
5
194664749.005.png 194664749.006.png
Zgłoś jeśli naruszono regulamin