Sony Ericsson T310 instrukcja rozbiórki.pdf

Working Instructions, SP/Mechanical

Applicable for T310/T312

Contents

Disassembly Front / Frame ............................................................................................ 2

Reassembly Front / Frame ............................................................................................. 5

Replacement of Mechanical Parts ................................................................................. 7

3.1

Microphone........................................................................................................ 7

3.2

Front cover......................................................................................................... 9

3.3

Co-brand inlay ................................................................................................. 10

3.4

Joystick button................................................................................................. 11

3.5

Speaker assembly ............................................................................................ 12

3.6

Keypad............................................................................................................. 13

3.7

LCD carrier assembly...................................................................................... 14

3.8

Volume key ..................................................................................................... 15

3.9

Buzzer gasket................................................................................................... 16

3.10

Vibrator unit .................................................................................................... 17

3.11

Dome switch foil ............................................................................................. 18

3.12

Antenna flex foil.............................................................................................. 18

3.13

Front bezel ....................................................................................................... 20

Label............................................................................................................................... 22

Revision History ............................................................................................................ 23

3/000 21-1/FEA 209 544/70 C

Approved according to 000 21-LXE 107 42/1

Sony Ericsson Mobile Communications AB

Working Instructions , SP/ Mechanical

Disassembly Front / Frame

Tools

•

Torque screwdriver set to 20Ncm

Torx T6 bit

Tweezers with rounded and polished tip (not serrated)

Guitar pick, 1mm thick, (Fender heavy)

Instruction

Use cotton gloves!

Figure

Instruction

Note

Remove the battery cover by

pushing it towards the bottom

of the phone. Remove the

battery and the SIM-card.

Fig. 1.1

Release one side of the

antenna cover by inserting the

tool between cover and frame

as indicated. Push gently

upwards to release the latch.

Fig. 1.2

Repeat the same procedure as

above on the other side of the

antenna cover.

Slide the cover in the direction

of the arrows. This releases

the latches in the bottom of the

cover and it can be pulled

straight out from the frame.

The latches will be

deformed if the top of the

cover is pulled out before

the latches are completely

free.

Fig.1.4

3/000 21-1/FEA 209 544/70 C

2(23)

Sony Ericsson Mobile Communications AB

Working Instructions , SP/ Mechanical

Figure

Instruction

Note

Remove the two screws on the

top of the phone.

Be careful not to damage

the antenna with the

screwdriver!

Fig.1.5

Insert the tool in the gap

between the bezel and the

front (1). The gap can be

widened by gently pressing

the front away from the frame.

The tool should be pushed

straight in at an angel of

approx. 45 degrees.

Fig.1.6

The goal is to get the tool

between the bezel and the rest

of the front (2) to release the

latch.

Repeat the same procedure on

the other side of the phone.

Fig.1.7

Lift the bezel gently

Fig .1.8

Insert the tool in the gap

between the front and the

frame. The gap can be

widened by gently pressing

the front away from the frame.

The tool should be pushed

straight in at an angel of

approx. 45 degrees and gently

slide down to the bottom.

The goal is to get the tool

between the bezel and the rest

of the front to release the

latches.

Repeat the same procedure on

the other side of the phone.

Fig.1.9

3/000 21-1/FEA 209 544/70 C

3(23)

Sony Ericsson Mobile Communications AB

Working Instructions , SP/ Mechanical

Figure

Instruction

Note

Remove the front from the

frame.

Fig.1.10

NOTE:

Lift the front gently. Be aware

of the hooks at the bottom of

the frame.

Remove the four remaining

screws.

Fig.1.11

The front, the frame and the

circuit board are now

separated.

3/000 21-1/FEA 209 544/70 C

4(23)

Sony Ericsson Mobile Communications AB

Working Instructions , SP/ Mechanical

Reassembly Front / Frame

Tools

•

Torque screwdriver set to 20Ncm

Torx T6 bit

Tweezers with rounded and polished tip (not serrated)

Guitar pick, 1 mm thick, (Fender heavy)

Instruction

Use gloves!

Figure

Instruction

Note

On all units one support pad

SXA 104 9219 must be added.

Use tweezers to put a pad on

D600.

Put the shielding can in the

frame.

Fig. 2.1

Place the PCB assembly in the

frame.

Insert the screws in marked

order.

Fig. 2.2

3/000 21-1/FEA 209 544/70 C

5(23)

Sony Ericsson Mobile Communications AB

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: