plate-rack-polka kuchenna wiszaca.pdf

(384 KB) Pobierz
Plate Rack
P
late Rack
This plate rack is a perfect place to display your collectible plates. Or hang it in a
convenient spot on your kitchen wall and store your most frequently used dishes and cups.
Materials
  3 linear feet of 1 x 8 pine
  10 linear feet of 1 x 6 pine
  5 linear feet of 1 x 4 pine
  10 linear feet of 3/8”-diameter dowel
rod
Hardware
  20 1-5/8” wood screws
  4 hanging hooks
Cutting List
Code
Description
Qty.
Materials
Dimensions
A Rack Sides
2 1 x 6 pine
26” long
B Rack Top/Bottom
2 1 x 6 pine
24-1/2" long
C Rack Middle
1 1 x 4 pine
24-1/2" long
D Rack Ledge
1 1 x 8 pine
28" long
E Rack Base
1 1 x 4 pine
24-1/2" long
F Dowel
4 3/8”dowel rod 25” long
1
108207053.048.png 108207053.049.png 108207053.050.png 108207053.051.png 108207053.001.png 108207053.002.png 108207053.003.png 108207053.004.png 108207053.005.png 108207053.006.png 108207053.007.png 108207053.008.png 108207053.009.png 108207053.010.png 108207053.011.png 108207053.012.png 108207053.013.png 108207053.014.png 108207053.015.png 108207053.016.png 108207053.017.png 108207053.018.png 108207053.019.png 108207053.020.png 108207053.021.png 108207053.022.png 108207053.023.png 108207053.024.png 108207053.025.png 108207053.026.png 108207053.027.png 108207053.028.png 108207053.029.png 108207053.030.png 108207053.031.png 108207053.032.png 108207053.033.png 108207053.034.png 108207053.035.png 108207053.036.png 108207053.037.png 108207053.038.png 108207053.039.png 108207053.040.png
Special Tools and Techniques
Clamps
Making the Rack
1. Cut two Rack Sides (A) from 1 x 6 pine, each measuring 26 inches.
2. Using Figure 1 as a guide, clamp both Rack Sides (A) together to hold them while cutting out
a quarter-circle from the ends of the Rack Sides (A).
Figure 1
3. Using Figure 2 as a guide, mark the positions for the dowel rod holes. Using a 3/8-inch-
diameter drill bit, drill into the marked spots 3/8” deep. (Placing a piece of masking tape
around the bit 3/8”from the tip can do this.)
4. Cut two Rack Top/Bottom (B) from 1 x 6 pine, each measuring 24-1/2 inches.
5. Place the two Rack Sides (A) on edge on a level surface parallel to each other and 24-1/2
inches apart. As shown in Figure 3 , place one Rack Top/Bottom (B) perpendicular between
the Rack Sides (A) 4-1/2 inches up from the cut ends of the Rack Sides (A). Place the
remaining Top/Bottom between the Rack Sides (A). Apply glue to the meeting surfaces, and
screw through the face of the Rack Sides (A) into the ends of the Rack Top/Bottoms (B),
using three 1-5/8” screws on each side.
6. Cut one Rack Middle (C) from 1 x 4 pine, measuring 24-1/2 inches long
7. Place the Rack Middle (C) perpendicular between the Rack Sides (A) 13 inches above the cut
ends of the Rack Sides (A) and screw in place.
8. Cut one Rack Ledge (D) from 1 x 8 pine, measuring 28 inches.
2
108207053.041.png
9. Place the Rack Ledge (D) over the ends of the Rack Sides
(A) as shown in Figure 4 . Apply glue to the meeting
surfaces. Screw through the face of the Rack Top (D) into
the ends of the Rack Sides (A) using three 1-5/8”screws on
both ends.
10. Cut one Rack Base (E) from 1 x 4 pine measuring 24-1/2
inches.
11. Place the Rack Base (E) below the Rack Bottom (B)
between the Rack Sides (A) as shown in Figure 5. Apply
glue to the meeting surfaces. Screw through the face of the
Rack Sides (A) into the end of the Rack Base (E). Also
screw through the face of the Rack Bottom (B) into the edge
of the Rack Base using three 1-5/8”screws on both sides.
Adding the Dowel Rods
1. Cut four Dowels (F) from 3/8-inch diameter dowel rod, each
measuring 25 inches.
2. Wipe a small amount of glue in the holes drilled in the Rack
Sides (A). Place one end of the dowel rod into one Rack
Side (A) and slightly bending the rod, place the other end
into the opposing hole on the other Rack Side (A).
Figure 2
Figure 3
3
108207053.042.png
Figure 4
Figure 5
4
108207053.043.png
Finishing
1. Fill any cracks, crevices, or screw holes with
wood filler.
2. Thoroughly sand all surfaces of the
completed plate rack.
3. Seal and paint or stain your completed plate
rack the color of your choice.
4. Attach the hooks to the Rack Base (E). Then stand back and admire!
Enjoy other indoor and outdoor
projects from
www.wowimadeit.com !
5
108207053.044.png 108207053.045.png 108207053.046.png 108207053.047.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin