MicroNet Sensors.EN.pdf
(
195 KB
)
Pobierz
MN-Sx, MN-SxHT,
MN-S4-FCS,
and MN-S4HT-FCS
I/A Series
®
MicroNet
™
Sensors
General Instructions
Application
I/A Series MicroNet Sensors are wall-mounted digital
temperature and humidity sensors for use with
I/A Series MicroNet Controllers. These sensors feature
Sensor Link (S-Link) communication protocol that
provides a simple two wire interface for power and
exchange of sensor and subbase information.
Available in twelve models, these I/A Series MicroNet
Sensors provide integral analog to digital conversion
for elimination of electrical interference between
sensor and controller. An optional wiring connection
allows access to the MicroNet L
ON
W
ORKS
®
network
(LON
®
) via a L
ON
W
ORKS
network jack on the left side
of each sensor. This jack allows direct connection to a
PC running WorkPlace Tech Tool (WP Tech) or a third
party Network Management Tool. Each sensor also
provides an S-Link jack on the right side for connecting
to a PDA running Pocket I/A software.
MN-S1
MN-S1HT
MN-S2
MN-S2HT
I/A Series MicroNet Sensors are suitable for direct-wall,
2 x 4 electrical box, 1/4 DIN electrical box, or surface
box mounting.
Model Chart
MN-S3
MN-S3HT
MN-S4
MN-S4HT
See Table-1 on page 2 for a chart of the models.
MN-S4-FCS
MN-S4HT-FCS
MN-S5
MN-S5HT
Printed in U.S.A.
12/09
©
Copyright 2009 Schneider Electric All Rights Reserved.
F-26277-9
Table-1
MN-Sxxx Model Chart.
Model
Description
Keypad
Display
Temperature
Sensor
Temperature and
Humidity Sensor
MN-S1
MN-S1HT
Sensor only
None
None
MN-S2
MN-S2HT
Sensor with override
One-button
LED Override Status Indication
Digital LCD
a
and LE D Override Status
Indication
MN-S3
b
MN-S3HT
b
Sensor with setpoint adjustment and override
Three-button
Digital LCD
c
and LED Override Status
Indication
Sensor with setpoint, override, and controller
mode functions
MN-S4
b
MN-S4HT
b
Six-button
Digital LCD
c
and LED Fan Status
Indication
Sensor with setpoint, On/Off and Fan speed
functions
MN-S4-FCS
b
MN-S4HT-FCS
b
Six-button
Digital LCD
c
, LED Override Status, and
Emergency Heat Indication
Sensor with setpoint, override, controller mode
functions, and emergency heat key
MN-S5
b
MN-S5HT
b
Seven-button
a
LCD displays value and setpoint.
b
Allows viewing of alarms and diagnostics.
c
LCD displays values, setpoints, and controller mode functions.
2
©
Copyright 2009 Schneider Electric All Rights Reserved.
F-26277-9
Applicable Documentation
F-Number
Description
Audience
Purpose
I/A Series MicroNet 100,
150, and 200 Series
Controllers Installation
Instructions
– Application Engineers
– Installers
– Service Personnel
– Start-up Technicians
Provides step-by-step mounting and installation instructions for the
I/A Series MicroNet 100, 150, and 200 Series Controllers.
Also includes checkout and LED indication sections.
F-26266
– Application Engineers
– Installers
– Service Personnel
– Start-up Technicians
I/A Series MicroNet 50
Series Controllers
Installation Instructions
Provides step-by-step mounting and installation instructions for the
I/A Series MicroNet 50 Series Controller. Also includes checkout
and LED indication sections.
F-26617
I/A Series MicroNet
VAV Series (MNL-V1RVx
and MNL-V2RVx)
Controllers Installation
Instructions
– Application Engineers
– Installers
– Service Personnel
– Start-up Technicians
Provides step-by-step mounting and installation instructions for the
I/A Series MicroNet MNL-V1RVx and MNL-V2RVx VAV Controllers.
Also includes checkout and LED indication sections.
F-26282
I/A Series MicroNet
VAV Series (MNL-V3RVx)
Controller Installation
Instructions
– Application Engineers
– Installers
– Service Personnel
– Start-up Technicians
Provides step-by-step mounting and installation instructions for the
I/A Series MicroNet MNL-V3RVx VAV Controller. Also includes
checkout and LED indication sections.
F-26284
I/A Series MicroNet Fan
Coil Controllers with High
Voltage Relay(s)
Installation Instructions
– Application Engineers
– Installers
– Service Personnel
– Start-up Technicians
Provides step-by-step mounting and installation instructions for the
I/A Series MicroNet MNL-11RF2 and MNL-13RF2 Controllers.
Includes instructions for network wiring, installation on a L
ON
W
ORKS
network, checkout, and LED indication.
F-26887
– Application Engineers
– Installers
– Service Personnel
– Start-up Technicians
I/A Series WorkPlace Tech
Tool Engineering Guide
(for version 3.1)
Provides engineering and technical information for applying and
using all aspects of WorkPlace Tech Tool, version 3.1 software.
F-26580
– Application Engineers
– Installers
– Service Personnel
– Start-up Technicians
I/A Series WorkPlace Tech
Tool 3.2 Engineering Guide
Provides engineering and technical information for applying and
using all aspects of WorkPlace Tech Tool, version 3.2 software.
F-26988
– Application Engineers
– Installers
– Service Personnel
– Start-up Technicians
I/A Series WorkPlace Tech
Tool 4.0 Engineering Guide
Provides engineering and technical information for applying and
using all aspects of WorkPlace Tech Tool, version 4.0 software.
F-27254
– Application Engineers
– Installers
– Service Personnel
– Start-up Technicians
Provides engineering and technical information to assist in
designing a complete MicroNet controller system using different
architectures, components, and software.
I/A Series MicroNet
System Engineering Guide
F-26507
– Application Engineers
– Installers
– Service Personnel
– Start-up Technicians
I/A Series WorkPlace Tech
Tool User’s Guide (for
version 3.1)
Provides step-by-step instructions for using WorkPlace Tech Tool,
version 3.1 software.
F-26304
– Application Engineers
– Installers
– Service Personnel
– Start-up Technicians
I/A Series WorkPlace Tech
3.2 Tool User’s Guide
Provides step-by-step instructions for using WorkPlace Tech Tool,
version 3.2 software.
F-26987
– Application Engineers
– Installers
– Service Personnel
– Start-up Technicians
I/A Series WorkPlace Tech
4.0 Tool User’s Guide
Provides step-by-step instructions for using WorkPlace Tech Tool,
version 4.0 software.
F-27255
F-26277-9
©
Copyright 2009 Schneider Electric All Rights Reserved.
3
Installation
The I/A Series MicroNet Sensor is packaged disassembled in one box and consists of three
major parts:
•
A pre-wirable base plate for wiring to the controller S-Link and MicroNet L
ON
W
ORKS
network (LON) connections
•
An electronic assembly containing the sensors and associated circuitry
•
A removable cover
Inspection
Inspect carton for damage. If damaged, notify carrier immediately. Inspect sensors for
damage upon receipt.
Requirements
(These items not provided)
•
Installer must be a qualified technician
•
Job wiring diagrams
•
Tools:
–
Drill and bits for mounting screws
–
Level
–
Static protection wrist strap
•
Two mounting screws (dry-wall anchors for direct-wall mount)
•
Accessories (if required)
–
AT-1104
Cast aluminum guard with steel base plate
–
AT-1155
Clear plastic guard with solid and ring base, tumbler type key lock
–
AT-1163
Wire guard with steel base plate
–
MNA-STAT-1
Replacement covers (qty. 12)
–
MNA-STAT-2
Designer inserts for MN-S1 model (qty. 25)
Precautions
General
Caution:
Disconnect power before installing or removing the cover.
Failure to observe this warning can damage the sensor.
•
Follow Static Precautions when installing this equipment.
•
Use copper conductors that are suitable for 167 °F (75 °C).
•
Make all connections according to electrical wiring diagram, national and local electrical
codes.
Static Precautions
Static charges damage electronic components. The microprocessor and associated circuitry
are extremely sensitive to static discharge. Use the following precautions when installing,
servicing, or operating the system.
•
Work in a static-free area.
•
Discharge static electricity by touching a known, securely grounded object.
•
Use a wrist strap connected to earth ground when handling the controller’s printed
circuit board.
4
©
Copyright 2009 Schneider Electric All Rights Reserved.
F-26277-9
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in residential installations. This
equipment generates, uses, and can radiate radio frequency energy and may cause harmful
interference if not installed and used in accordance with the instructions. Even when
instructions are followed, there is no guarantee that interference will not occur in a particular
installation. If this equipment causes harmful interference to radio or television reception—
which can be determined by turning the equipment off and on—the user is encouraged to
try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the receiver
is connected.
•
Consult the dealer or an experienced radio/television technician for help.
Canadian Department of Communications (DOC)
This class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Location
I/A Series MicroNet Sensors are suitable for indoor use only.
Caution:
•
Avoid locations where excessive moisture, corrosive fumes, vibration, or explosive
vapors are present.
•
The humidity sensing element of MN-SxHT and MN-S4HT-FCS models will recover
from short term exposure to liquid water or condensation. Repeated exposure will
degrade the performance of the sensor.
•
Avoid electrical noise interference. Do not install near large contors, electrical
machinery, or welding equipment.
•
Locate where ambient temperatures do not exceed 122 °F (50 °C) or fall below 32 °F
(0°C) and relative humidity does not exceed 95% or fall below 5%, non-condensing.
Failure to observe these precautions can damage the sensors.
Locate the I/A Series MicroNet Sensor on an inside wall where the sensor is exposed to at
least 30 feet (9 meters) per minute of unrestricted air circulation. The location should
represent the average temperature in the room or space. Make certain sensor is located out
of direct sunlight, away from sources of heat or cold, and away from concealed ducts or
pipes.
F-26277-9
©
Copyright 2009 Schneider Electric All Rights Reserved.
5
Plik z chomika:
origator
Inne pliki z tego folderu:
MicroNet BACnet Plant Controller.EN.pdf
(244 KB)
MicroNet Sensors.EN.pdf
(195 KB)
MN 50 MicroNet Controller.EN.pdf
(129 KB)
TAC IA Series UNC-520.EN.pdf
(227 KB)
MNB-300 MicroNet BACnet Unitary Controller.EN.pdf
(242 KB)
Inne foldery tego chomika:
Karty katalogowe
Zgłoś jeśli
naruszono regulamin