Cabinet - Buffet And China Cabinet Plans.pdf - plans(1) - gerwazy762

Free Woodworking Plans: Buffet and China Cabinet Plans, Home Improvemen...-How To Build Stairs, Decks, Sheds, Picnic Tables, How to Build a House

Buffet and China Cabinet Plans

file:///C|/Documents and Settings/raimondo/Documenti/tele.../daveosborne/www.daveosborne.com/dave/projects/buffet.htm (1 of 11)09/09/2005 13.44.40

Free Woodworking Plans: Buffet and China Cabinet Plans, Home Improvemen...-How To Build Stairs, Decks, Sheds, Picnic Tables, How to Build a House

file:///C|/Documents and Settings/raimondo/Documenti/tele.../daveosborne/www.daveosborne.com/dave/projects/buffet.htm (2 of 11)09/09/2005 13.44.40

Free Woodworking Plans: Buffet and China Cabinet Plans, Home Improvemen...-How To Build Stairs, Decks, Sheds, Picnic Tables, How to Build a House

file:///C|/Documents and Settings/raimondo/Documenti/tele.../daveosborne/www.daveosborne.com/dave/projects/buffet.htm (3 of 11)09/09/2005 13.44.40

Free Woodworking Plans: Buffet and China Cabinet Plans, Home Improvemen...-How To Build Stairs, Decks, Sheds, Picnic Tables, How to Build a House

Materials Needed

1 - 4x8x1/4" Oak G1S plywood for upper back

1 - 4x8x1/4" Oak G2S plywood for lower back and door panels

4 - 4x8x3/4" Oak G2S plywood for gables shelves, drawer fronts, tops and

bottoms

1 - 4x8x1/2" Oak or G1S plywood for drawers

3 pieces 1x6x5' Oak S4S for face frame and doors

11 pieces 1x6x6' Oak S4S

1 piece crown molding 3 1/4"x 6'

1 piece crown molding 3 1/4"x 7'

2 pieces 3 mil glass cut to fit (approximately 28x35)

2 pairs bottom mount 16" drawer slides (Blum)

1 box flathead wood screws # 6x5/8" for slides

6 pairs 3/8" overlap self closing cabinet hinges (Amerock)

file:///C|/Documents and Settings/raimondo/Documenti/tele.../daveosborne/www.daveosborne.com/dave/projects/buffet.htm (4 of 11)09/09/2005 13.44.40

Free Woodworking Plans: Buffet and China Cabinet Plans, Home Improvemen...-How To Build Stairs, Decks, Sheds, Picnic Tables, How to Build a House

10 door and drawer pulls

2 lbs 1 1/2" bright finish nails

1 pint carpenter's yellow wood glue

Instructions

Rip the plywood to the sizes in the following cutting list.

Cutting List

Upper Cabinet:

2 end gables at 14 3/8 x 39 1/2

1 center gable at 14 1/8 x 39 1/2

4 shelves at 14 1/8 x 29 15/16

2 pieces for the top and bottom at 14 3/8 x 61 1/8

Lower Cabinet:

2 gable ends at 16 1/8 x 35 1/2

1 center gable at 15 7/8 x 30 3/4

2 shelves at 15 7/8 x 28 7/16

1 top at 16 1/8 x 59 1/4

1 bottom at 16 1/8 x 58 1/4

First layout the gables for each unit. Cabinet plywood is considered G2S (good 2

sides), but one side is usually a bit better than the other. Always rip the best

side up on a table saw and the best side down with a circular saw. Use a sharp

blade with the highest number of teeth for finishing. Lay the best sides of the

gables away from each other, they will be on the outside of the cabinet. Lay out

the gables for where the shelves and top and bottoms will go. We want to dado

these pieces in. Either use a dado blade with the table saw (preferred) or use a

router and jig. See article: Dado Jig for the Router http://www.daveosborne.

com/dave/articles/routerjig.php

For all dados cut in 1/4" deep the full thickness of the board. The Face Frame

drawing shows which piece overlaps and which piece comes to the other. The

hatched line shows the gables and tops and bottoms. Refer to the Cutting List,

these are exact sizes, the more accurate you are here the better the cabinet

will turn out. Remember to dado out for the back of each unit with 1/4" plywood.

file:///C|/Documents and Settings/raimondo/Documenti/tele.../daveosborne/www.daveosborne.com/dave/projects/buffet.htm (5 of 11)09/09/2005 13.44.40

Cabinet - Buffet And China Cabinet Plans.pdf

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: