Installation_Instructions_ODIS_Engineering_R5_0_6_EN.pdf

(983 KB) Pobierz
Installation Instructions
for Release 5.0
1080862098.028.png
Offboard Diagnostic Information System Engineer-
ing
Installation Instructions for Release 5.0.6.
Contents
1
2
3
Establishing the preconditions ........................................................................4
3.2
Uninstalling existing installations.....................................................................4
3.3
Running the installation routine .......................................................................4
3.4
Installing the D-PDU API.................................................................................5
4
5
6
Configuring the mail client.............................................................................10
6.3
Help ..............................................................................................................10
ODIS Engineering Team, Tel. +49 (5361) 9 - 16 1 32
Page 2 of 10
1080862098.029.png 1080862098.030.png 1080862098.031.png 1080862098.001.png 1080862098.002.png 1080862098.003.png 1080862098.004.png
 
Offboard Diagnostic Information System Engineer-
ing
Installation Instructions for Release 5.0.6.
1 Introduction
This document describes the steps required to successfully install the design engineer diagnostic
tester, OFFBOARD DIAGNOSTIC INFORMATION SYSTEM Engineering, in the following referred
to as Engineering Diagnostic Tester. The installation process consists of the following four main
steps:
1.
Configuring the computer/tester,
2.
Installing the application,
3.
Installing the runtime data and
4.
Configuring the application.
The individual steps are described in the following sections.
2 Configuring the computer/tester
The vehicle's diagnostic connection for the Engineering Tester is not reliably standby-capable.
! It is therefore recommended to adjust the computer's power options in such a way that
neither standby mode nor idle mode are enabled.
Switching manually to the computer's operating modes mentioned should also be avoided when
using the Engineering Tester.
The settings for the power options are available at Start → System control → All system control
elements → Power options.
Figure 1 shows the settings required for standby. It is also advisable to change the settings in the
power options to "Do nothing" when closing the tester.
Figure 1: Settings for the power options
ODIS Engineering Team, Tel. +49 (5361) 9 - 16 1 32
Page 3 of 10
1080862098.005.png 1080862098.006.png 1080862098.007.png 1080862098.008.png 1080862098.009.png 1080862098.010.png 1080862098.011.png 1080862098.012.png
 
Offboard Diagnostic Information System Engineer-
ing
Installation Instructions for Release 5.0.6.
3 Installing the application
Please note Chapter 3.4.
3.1 Establishing the preconditions
1.
To install the application, you require administrator rights on your PC.
2.
If you do not have a valid licence, please start the procurement transaction via the product
Installation is possible with an initiated licence. However, to start and use the application, you
require a valid licence.
3.
Download the OFFBOARD DIAGNOSTIC INFORMATION SYSTEM Engineering installation
package from the product website www.dne-elektronik.de :
PRD-ODISEngin_windows_5.0.6_TEMR140.exe
3.2 Uninstalling existing installations
If there is an older version of Engineering Diagnostic Tester on your PC, this old version will need
to be completely uninstalled first. To do this, use the corresponding link in the start menu and re-
start the computer.
3.3 Running the installation routine
Start setup by right-clicking on the downloaded installation package: "Run as administrator", ( ! )
even if you are already logged on as the administrator , and follow the instructions of the instal-
lation wizard. You can specify any path as desired when selecting the target directory for installing
the application and the diagnostic components. You do not have to use the proposed default path.
However, it is practical for the event that you require any support.
In the dialogue for selecting the certificate, enter the path for the licence file (e.g. "license.dat").
Note :
Do not remove the check mark from "Copy to installation directory". The application will then copy
the licence file to the installation directory and manage it there.
During the installation process, you will be requested to select the target platform (computer hard-
ware) for the installation. For this, the items "* with VAS 5054 radio head" and "* with VAS 6154"
are provided (cf. Figure 2) .
Please select radio head VAS 5054 for normal CAN diagnosis.
ODIS Engineering Team, Tel. +49 (5361) 9 - 16 1 32
Page 4 of 10
1080862098.013.png 1080862098.014.png 1080862098.015.png 1080862098.016.png 1080862098.017.png 1080862098.018.png 1080862098.019.png
 
Offboard Diagnostic Information System Engineer-
ing
Installation Instructions for Release 5.0.6.
Figure 2: Selecting the target platform
3.4 Installing the D-PDU API
There is a setup wizard for installing the Softing D-PDU API, which is activated automatically by the
setup routine of the Offboard Diagnostic Information Engineering Diagnostic Tester.
In some cases it could happen that the setup routine may demand for your intervention.
If that is the case you have to note following instructions:
- Please click “Next” respectively “Weiter” according to Figure 3
- Please click again “Next” respectively “Weiter” in the following dialogue without taking
changes (Figure 4) .
ODIS Engineering Team, Tel. +49 (5361) 9 - 16 1 32
Page 5 of 10
1080862098.020.png 1080862098.021.png 1080862098.022.png 1080862098.023.png 1080862098.024.png 1080862098.025.png 1080862098.026.png 1080862098.027.png
 

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin