BMX304GBBTR1.pdf

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 01

www.cobra.it

BMW

X 3*

YEAR 04 ﬁ

PETROL

DIESEL

MAKE

MOD.

* Models with original equipment keyless entry system.

ALARM/SIREN

POSITION

Position the compact alarms and the sirens in the engine compartment, on the shock absorber,

passenger’s side.

CENTRAL UNIT POSITION

The modular systems and the modules should be positioned behind the right lateral glove compartment,

passenger’s side.

POWER SUPPLY

+30: connect to the 4 mm 2 WHITE/RED wire located in a multiway connector at the entrance of the fuse

box.

- 31: Connect with a cable terminal to one of the original ground terminals located behind the left lateral

bulkhead, driver’s side.

IGNITION WIRE

+15/54: Connect to the VIOLET/YELLOW wire, at the position nr.13, in the 54 way black connector, on

the coming out of the operating central located behind the glove compartment, passenger’s side.

DIRECTION INDICATORS

The vehicle has the direction indicators lines divided, so connect to the following wires using 6 diodes:

(ant. left) BLUE/GREEN at the position nr.50, (ant. lat.) BLUE/YELLOW at the posiion nr.18, (post. left)

BLUE/GREEN at the position nr.1, (ant. right) BLUE/ BROWN at the position nr.11, (ant. lat.)

BLUE/YELLOW at the position nr. 3 and (post. right) BLUE/BROWN at the position nr. 43 located in the

54 way black connector placed in the module integrated to the position/antidazzle lights control switches.

ELECTRIC WINDOWS

Comfort closing

Negative control signal

The locking of the electric windows is obtained timing the BLUE/RED locking wire located at the position

nr. 22, in the connector coming out of the central doors locking unit, behind the glove compartment,

passenger’s side. Refer to the fitting diagram nr.199.

ACTIVAT./DEACTIVATION

CONTROLS

Connections antitheft/vehicle

Art.38XX Vehicle Position

YELLOW/BLACK WHITE coming out central doors locking unit

GREY/BLACK LIGHT BLUE coming out central doors locking unit

VIOLET/WHITE ground car body

ORANGE ground car body

VIOLET ground car body

ORANGE/WHITE ground car body

Note: after having programmed the on/off controls of the antitheft, cut the WHITE/BLACK wire, at the

position nr. 20, in the wiring harness coming out of the 54 way black connector, in the central position on

respect of others connectors located in the central locking unit placed behind the passenger’s side glove

compartment.

IMMOBILISATION POINT

Fuel pump

Cut the 1,5 mm 2 VIOLET/BLACK wire at the position nr.4, in the 13 way connector, in the central under

the dashboard.

STARTER

+50: Cut the BLACK/LIGHT BLUE wire located in the wiring harness coming out of the ignition key.

BONNET SWITCH

Install an additional switch on the front headlamp support grill, driver’s side.

DOORS SWITCH

Connect to the 0,5 mm 2 RED/BLUE wire, in the wiring harness coming out of the connector of the central

doors locking unit located behind the glove compartment, passenger’s side.

Attention: this is a positive control signal. It is suggested to reverse the polarity by means of a microrelay.

BOOT SWITCH

Connect to the WHITE/BROWN wire located in the wiring harness behind the sill cover, driver’s side.

HORN CONTROL

Positive control

Connect to the VIOLET/BLUE wire in the wiring harness above the brake pedal that goes through the

engine compartment.

Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed

as per the instructions given on the product installation manual.

bmx304gbbtr1.doc

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 01

www.cobra.it

FITTING DIAGRAM NR. 199

Diagram for the connection of Art. 1055 to make the windows locking on

BMW serie 3

Temporized relay

Central locking unit behind

passenger’s side glove compartment

ART.1055

1 2 3 4 5 6 7

+30

BLUE/RED

pos. nr.22

BROWN

(negative control

at antitheft on)

ground

Door switch

driver’s side

ground

Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed

as per the instructions given on the product installation manual.

bmx304gbbtr1.doc

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: