kwiat2.pdf

(34 KB) Pobierz
8178757 UNPDF
$ Flower
Copyright 1998-99 Stephen Hecht. All Rights Reserved
A dollar bill produces a model 100mm long with a bloom of 40mm diameter. The bloom is adapted from Herman
Lau’s Flower-in-a-Pot. That bloom can also be used here, resulting in a shorter stem and a smaller bloom
diameter (but with 8 petals, not 6).
C
C
C
A
B
4. Valley-fold and
unfold halfway to C.
Turn over.
1. Valley-crease at
quarters. Turn over.
2. Pivot at A, bring B
to 1/4 line, marking
only at C.
3. Valley-fold and
unfold at C.
1/2
5. Swing in sides.
6. Swing up on
existing crease.
7. Valley and unfold
through all layers of
the upper flap. Unfold
completely. Rotate
half turn. Turn over.
8. Valley on existing
creases, extending to
edges.
9. Use existing valley-
creases to squeeze in
mountain-fold angle
bisectors.
Repeat on left.
10. Sink hexagonally
halfway. (Open out
to find landmarks.)
Alternate method, using
Lau’s 8-petalled flower:
1. Crease at quarters.
2. Water-bomb base at
one end.
3. Squash the 4
triangular flaps of the
water-bomb base: two
loose flaps in front, two
flaps attached to the
rest of the bill in back.
4. Octagonally sink tip
halfway.
11. Mountain-fold
entire top and unfold.
8178757.001.png
$ Flower (continued)
Copyright 1998-99 Stephen Hecht. All Rights Reserved
12. Gather up 4 edges
perpendicularly.
13. Wrap edges.
Reverse below valley-
fold (where indicated).
Entire bottom of bill
swings behind and up.
15. Note that the
sunken assembly has
remained fixed. Swing
one flap to the left.
14. Continue collasping
on existing creases.
1/2
15-17
16. Mountain-fold on
existing crease,
tucking inside.
17. Swing flap back
to the right. Repeat
15-17 on left. Rotate
half-turn.
18. Add mountain-
creases halfway
between existing
valleys. Inner ones
don’t have to go all
the way up.
19. Crease forwards
and backwards. Make
the longer fold first, then
use it to help locate the
shorter.
20 Add more creases.
Turn over.
21. Crease angle-
bisector, to center-line.
Repeat on right.
22. Fold model in half,
swinging 2 small flaps
to the left behind at the
top.
23. Outside crimp.
Mountain-folds exist,
valley-folds are new.
8178757.002.png
$ Flower (continued)
Copyright 1998-99 Stephen Hecht. All Rights Reserved
24-26
24. Lift one flap.
25. Pleat on existing
creases.
26. Swing flap back
down. Repeat 24-26
behind.
27. Sink long edge.
Closed-sink and keep
together at the top.
28. Spread pleats, reform creases from
18-20, Elias-stretching.
29. Closed sink
upper layer on
angle-bisector.
30. Roll and
tuck inside
sink. Swing
flap down.
31. Closed-sink.
Not quite an
angle-bisector.
33. Outside reverse fold the leaf (valley is
single-ply, mountain on dotted line). At the
same time, mountain the stem in quarters,
forming a tube. Where leaf joins stem, form
tiny gussets to avoid tearing.
Tuck loose paper at tip of leaf inside, behind
the sink from step 31. Curve and shape leaf.
32. Mountain a single
ply, flush with sink.
Swing flap back up.
Rabbit ear stem where it joins the bloom.
8178757.003.png
$ Flower (continued)
Copyright 1998-99 Stephen Hecht. All Rights Reserved
x6
34. This is the view between the
two thinnest petals. Valley and
mountain the lower corners of the
4 “loose” petals, locking the base
of the bloom.
35. Reverse-fold top edges of all
6 petals (about 1/3 of the angle).
Don’t flatten.
36. View from above the bloom. Pull
down tips of petals, while gently
flattening the center.
37. This is a single petal. Open and round
the sides of the petal, and mountain the
tip behind. Flatten the underside of the
petal, especially the thick petals adjoining
the stem.
38. Finished. (Ok, so it’s a generous picture,
but you get the idea.)
8178757.004.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin