Box - Brentwood with Turned and Carved Lids Plans.pdf - Projekty - stolarstwo - michalxmen

BENTWOOD BOXES

WITH TURNED AND

CARVED LIDS

Walnut, Curly Maple, Cherry

MAKING THE BENTWOOD BOXES

First, make a bending form for the main body of the box.

This can be fabricated from any scrap that can be glued

together to make up a sufficient thickness. This is then

band sawn and sanded to the inside profile of the finished

box. Undercut the face of the bending form at one point

to allow for the thickness of the lapped material underneath

the box's glue joint. Screw a thin strip of metal (I used a

scrap of aluminum siding) to the form underneath which

an end of the sidewall material should be inserted prior to

being wrapped around the form.

At this time, saw a clamping caul (see photos, below)

with a slightly greater radius than the bending form from

scrap material. This caul will protect the sidewall material

from the clamps.

The next consideration is the sidewall material itself.

There are three possibilities. First, the stock can be resawn,

planed and sanded to a thickness of 1/16". Second,

Constant-e's Hardware sells 1/16" veneer in cherry,

walnut and mahogany, even though those thicknesses

aren't listed in their most recent catalogs. Third, the

sidewall material can be glued-up from two thicknesses of

1/32" veneer, which is

widely available in a variety of species. I would recommend

using one of the new waterproof glues between the lamina-

tions, although I have built boxes using regular aliphatic

resin glue to bond the thicknesses of veneer.

Then, soak the sidewall stock in a tub of cool water for

twenty-four hours; dunk it briefly in warm water and take

it directly to the bending form. Tuck one end of this

softened, plasticized material under the metal strip on the

bending form. Wrap the remaining length around the form

and secure in place with clamps and the caul.

Four or five days later, remove the sidewall material

from the form and cut the profile of the lap joint. A bench

extension to which is nailed a piece of scrap sawn to the

inside radius of the box simplifies the cutting of the joint.

Then, glue the lap, wrap the sidewall material around

the form once again and clamp with the aid of the caul.

This time, however, do not insert the end of the sidewall

material under the form's metal strip. After being turned,

attached the box's bottom to the sidewalls with four 1/8 "

wooden pegs driven into predrilled holes.

CUTTING THE LAP JOINTS

A lap joint is be-

ing cut on the

bench extension.

1 This is the bench extension used to maintain the curved

form of the sidewall material during the cutting of the lap.

The clamping caul is visible on the right.

Here, the glued lap joint is being clamped with the aid of the

caul. Notice that the end of the sidewall material is not

positioned under the metal strip as it was during its initial clamping

for shape.

TURNING THE LID

AND THE BOTTOM

Screw a faceplate to a band-sawn turning blank with large

This is the same blank after being turned. Above the bead,

notice the flange that will fit inside the box's sidewalls.

sheet metal screws. Then, install it on the lathe.

DECORATING THE SURFACES

Before removing the parts from the lathe, sketch pencil

lines on the lid approximating the shapes to be created.

Then with gouges of various sweeps, define those lines (shown

above).

Remove material below the line (as shown above), and create

the stippled texture by repeatedly tapping a nail set into the

surface of the wood.

MATERIALS LIST

A Form

1 pc. 3X3/2

B Caul

1 pc. 1/ 2 X3 1/2X3 1/2

C Sidewall

1 pc. 1/16X 3 1/2X15

D Lid

1 pc. variable

E Bottom

1 pc. variable

F Pegs

4 pc. 1/8 X 1/8 X 1/2

Box - Brentwood with Turned and Carved Lids Plans.pdf

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: