Biostar_P4TDP.pdf

(148 KB) Pobierz
100950283 UNPDF
P4TDP JUMPER SETTING
Layout of P4TDP
K/B
&
Mouse
JKBV1
JCFAN1
JATXPWR2
1
JUSB1
JUSBV1
JCOM1
JPRNT1
I/O
JCOM2
JGAME1
INTEL 845D
2
JUSB4
JATXPWR1
BAT1
JUSBV4
J1
JDIMMVOLT1
1
2
AGP1
USB 2.0
Chip
(optional)
PCI1
JAUDIO1
1
2
JUSB3
JCDIN1
PCI2
2
INTEL ICH2
JUSB2
Codec
(optional)
2
JCMOS1
PCI3
1
JUSBV2_3
IDE1
PCI4
PRIMARY IDE CONN.
H/W
AUDIO
Chip
(optional)
SECONDARY IDE CONN.
PCI5
FLOPPY DISK CONN.
IDE2
FDD1
BIOS
JSFAN1
JWOL1
1
JPANEL1
1
1
2
24
CNR1
23
1
JKBMS1
100950283.027.png 100950283.028.png 100950283.029.png 100950283.030.png 100950283.001.png 100950283.002.png
P4TDP JUMPER SETTING
Jumpers, Headers, Connectors & Slots
Hard Disk Connectors: IDE1/ IDE2
The motherboard has a 32-bit Enhanced PCI IDE Controller that
provides PIO Mode 0~4, Bus Master, and Ultra DMA / 33/ 66/ 100
functionality. It has two HDD connectors IDE1 (primary) and IDE2
(secondary).
The IDE connectors can connect a master and a slave drive, so you can
connect up to four hard disk drives. The first hard drive should always be
connected to IDE1.
Floppy Disk Connector: FDD1
The motherboard provides a standard floppy disk connector that
supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This
connector supports the provided floppy drive ribbon cables.
Communication Network Riser Slot: CNR1
The CNR specification is an open Industry Standard Architecture, and it
defines a hardware scalable riser card interface, which supports audio,
network and modem only (slave card only) .
(If the function CODEC is onboard, then the CNR slot only support
slave card. But if the H/W Audio is onboard, then the CNR slot
support only primary card . )
Accelerated Graphics Port Slot: AGP1
Unlike the mouse ports, keyboard ports and printer ports this
motherboard does not have built in video facilities and therefore requires
a video card for one of the expansion slots. Your monitor will attach
directly to that video card. This motherboard supports video cards for
PCI and ISA slots but is also equipped with an Accelerated Graphics
Port (AGP). An AGP card will take advantage of AGP technology for
improved video efficiency and performance, especially with 3D graphics.
Peripheral Component Interconnect Slots: PCI1-5
This motherboard is equipped with 5 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for
expansion cards, which has, supplanted the older ISA bus standard in
most ports. This PCI slot is designated as 32 bits.
2
100950283.003.png
P4TDP JUMPER SETTING
Power Connectors: JATXPWR1/ JATXPWR2
JATXPWR2
(ATX 12V Power Conn.)
JATXPWR1
(ATX Main Power Conn.)
DIMM Power Selection Connector: JDIMMVOLT1
(Optional)
2
Jump Open==> 2.5V
Pin 1-2 on ==> 2.6V
Pin 3-4 on ==> 2.7V
Pin 5-6 on ==> 2.8V
Pin 7-8 on ==> 2.9V
JDIMMVOLT
(Default ==> 2.5V)
It strongly recommended to set DDR DIMM voltage in default setting
2.5V, and it for over voltage function.
Wake On LAN Header: JWOL1
Ground
5V_SB Wake up
WO L1
3
1
100950283.004.png 100950283.005.png 100950283.006.png 100950283.007.png 100950283.008.png 100950283.009.png 100950283.010.png 100950283.011.png 100950283.012.png
P4TDP JUMPER SETTING
Front USB Header: JUSB2/ JUSB3(Optional)
/ JUSB4(Optional)
1
Pin1,2 ==> +5V
Pin3,4 ==> Data(-)
Pin5,6 ==> Data(+)
Pin7,8 ==> Ground
Pin9 ==> KEY
Pin10 ==> NA
JUSB2/3/4
Basically JUSB1/2 supports USB1.1, but after adding an USB2.0 chip,
JUSB1/4(white) supports USB2.0.
Having an USB2.0 chip, JUSB1/4(white) supports USB2.0 and JUSB2/3
only supports USB1.1.
5V/ 5VSB Selection for USB: JUSBV1/2_3
/ JUSBV4(Optional)
1
Pin 1-2 on ==> 5V
JUSBV1/2_3/4
Pin 2-3 on ==> 5V_SB
5V/ 5VSB Selection for KB: JKBV1
1
Pin 1-2 on ==> 5V
JKBV1
Pin 2-3 on ==> 5V_SB
4
100950283.013.png 100950283.014.png 100950283.015.png 100950283.016.png 100950283.017.png
P4TDP JUMPER SETTING
5V/ 5VSB Selection for USB WAKE-UP: J1(Optional)
1
Pin 1-2 ==>
on
J1
Pin 2-3 ==> off
When VT6202 support 5V/5VSB Selection for USB WAKE-UP in on
mode, JUSB1 and JUSB4 will change to 5V_SB
Audio Subsystem: JAUDIO1/ JCDIN1
2
JAUDIO1
(Front Audio Header)
1
JCDIN1
(CD-ROM Audio-In Header)
Front Panel Connector: JPANEL1
PWR_LED
SLP
ON/OFF
IR
(+)
(+)
(-)
2
24
1
23
(+) (-)
SPK
RST
IR
HLED
SPK ==> Speaker Conn.
HLED ==> Hard Driver LED
RST ==> Reset Button
IR ==> Infrared Conn.
SLP ==> Sleep Button
PWR_LED ==> Power LED
ON/ OFF ==> Power-on Button
5
100950283.018.png 100950283.019.png 100950283.020.png 100950283.021.png 100950283.022.png 100950283.023.png 100950283.024.png 100950283.025.png 100950283.026.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin