CP243-1IT.pdf

back

Foreword

Product Information

Table of Contents

List of Figures

List of Tables

Introduction

SIMATIC NET

Features and Functions

Installation and Comissioning

CP 243-1 IT

Communications Processor

for Industrial Ethernet and

Information Technology

Configuration

Programming

Diagnosis

Appendix A: Technical Data

Appendix B: Example

Technical Manual

Appendix C: Timeouts

03/2003

J31069-D0429-U001-A0-7618

Passing on and reproduction of this document, or utilization and

revelation of its contents is prohibited without express permission.

patent is granted or a utiliy model is registered.

Exclusion of liability

Although we have checked the contents of this publication for

correspondence to the hardware and software described therein, we

cannot guarantee total agreement. The information in this publication is

reviewed at regular intervals and necessary corrections included in the

next releases.

Your suggestions are welcome.

Siemens AG

Automation & Drives

Postfach 4848

D-90327 Nuernberg

Subject to change without prior notice

Siemens-Aktiengesellschaft

J31069-D0429-U001-A0-7618

Classification of safety information

This document contains information which you must adhere to for your own per-

sonal safety and to avoid property damage. This information is highlighted with a

warning triangle and graded by degree of danger.

Danger

means that death or severe injury will occur if appropriate precautions are not

taken.

Warning

means that death or severe injury may occur if appropriate precautions are not

taken.

Caution

with a warning triangle means that minor injury may occur if appropriate precautions

are not taken.

Caution

without a warning triangle means that property damage may occur if appropriate

precautions are not taken.

Attention

means that an undesired result or state may occur if appropriate precautions are

not taken.

Note

indicates important information on the product, its handling or the particular part of

the documentation requiring special attention. Possible benefits make it advisable

to adhere to these recommendations.

Brands

SIMATIC

, SIMATIC NET

, SINEC

and SIMATIC NET Networking for Industry ®

are registered brands of Siemens AG.

The other designations in this publication may be brands whose use by third par-

ties for their own purposes may violate the rights of the owners.

Safety information on your product

Before you begin using the product described here, it is essential to read and ad-

here to the following safety information.

Qualified personnel

Only qualified personnel may commission and operate this device. For the purpose

of the safety notes in this manual, qualified personnel are those persons who are

authorized to commission, ground and tag devices, systems and electrical circuits

according to the standards of safety technology.

Intended use of hardware products

Adhere to the following information on the intended use of hardware products.

Caution

The device may only be used for the technical applications described in the cata-

log and only with products of Siemens or recommended by Siemens or devices

and components of other manufacturers which have been approved by Siemens.

Correct, safe operation of the product depends on correct transportation, correct

storage, installation and mounting as well as careful operator control and mainte-

nance.

Before you begin using the included sample program or your own programs, make

sure that no injury or property damage to man or machine can occur on the run-

ning systems.

EG note: Commissioning is prohibited until it can be determined that the machine

in which these components is to be installed meets the specifications of guideline

89/392/EWG.

03/03

Foreword

Purpose of this manual

This manual will be helpful when you use your CP 243-1 IT communications proc-

essor. It provides you with information on how to communicate with this communi-

cations processor via Industrial Ethernet and how to use the Information Technol-

ogy functions.

Prerequisites

A knowledge of this manual as well as the manual on SIMATIC S7-200 program-

mable controllers is required for understanding the functions of the CP 243-1 IT. In

addition, you will need a basic knowledge of such topics as TCP/IP, FTP, E-Mail,

HTML, Web Browser and Java.

Target group

This manual is written for engineers, programmers, commissioning personnel and

maintenance personnel with a general knowledge of automation and communica-

tion systems as well as user interface systems.

Sample program

This manual contains a sample program which gives you an example of how to

program your CP 243-1 IT. This program was prepared with STEP 7-Micro/WIN 32

V3.2.3 and will run on an S7-200 CPU (type 224). If you want to run this sample

program on another S7-200 CPU, you may have to adjust this CPU to the configu-

ration expected by our program.

CP 243-1 IT

J31069-D0429-U001-A0-7618

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: