samsung nc10.pdf
(
15393 KB
)
Pobierz
719858669 UNPDF
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
3. Disassembly and Reassembly
3-1. NC10 Disassembly and assembly
[Caution] Attention to red sentence.
Part
Picture
Description
2
1. Before disassembling the system, the AC adapter and the
battery have to be separated.
2. As shown in picture 1, adhere KNOB to the end closely
into the arrow direction, then push the battery up as shown
in picture 2.
1
1
3. When the battery is pushed upwards, it can be separated.
Main
System
4. Remove the BOTTOM screw.
IF only keboard is disassembled, remove only 3 BOTTOM
screws(ㅁ mark).
M2 x L8, Silver (15EA)
5. Remove the DOOR-MEMORY.
NC10
3-1
Winchester_NC10_Eng.indb 1
2008-09-20 오후 1:36:02
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
3. Disassembly and Reassembly
Part
Picture
Description
6. Remove the memory by pushing the ixed-tap out.
7. Push the Hook up inwards by using a pin-set as shown in
the picture, and then lift the key board up.
[Notice]
When you push the hook up, you have to be careful not to
scratch Topdp.
As shown in the picture, lift the top side of keyboard up and
then disassemble keyboard.
Main
System
8. Lift the Keyboard up, and then take the FPC out after
lifting the Connector Lock.
Take Keyboard FPC cable out after opening Keyboard
connector Lock.
3-2
NC10
Winchester_NC10_Eng.indb 2
2008-09-20 오후 1:36:13
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
3. Disassembly and Reassembly
Part
Picture
Description
9. As shown in the picture, separate the BOTTOM-
COVER(LAN Connector side irst) by widening the gap
between the BOTTOM-COVER and the TOP. (Be careful
not to make scratch in the gap using a wooden-driver.)
As shown in the picture, separate the BOTTOM-COVER
by widening the gap between the BOTTOM-COVER and
the TOP. (Be careful not to make scratch in the gap using a
wooden-driver.)
10. After removing the Screw for ixing HDD remove the
INSULATOR by lifting the HDD up to about 70 degrees
direction.
Main
System
[Notice]
When you life the HDD up, you shall not enforce excessive
strength.
11. Speaker CONN. INT Mic CONN., Power S/W CONN.
Touch-Pad FPC.
NC10
3-3
Winchester_NC10_Eng.indb 3
2008-09-20 오후 1:36:22
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
3. Disassembly and Reassembly
Part
Picture
Description
12. Remove the Antenna Cable which is connected with
wireless LAN, and then remove the Screw which ixes
WLAN. [Aux(Black)]
M2 x L4, Black (1EA)
1. White, Main
2. Black, Aux
13. Remove the Bluetooth Camera Cable and the LCD cable
CONN. and disassemble the W/L Antenna Cable.
14. Remove the Screw which ixes the Main Board and the
TOP and then separate Main Board from TOP.
M2 x L4, Black (2EA)
Main
System
15. Remove the both sides of Screw, which fasten the Hinge
and the TOP.
M2 x L4, Black (4EA)
16. Stand the Top Ass’y in a vertical direction.
3-4
NC10
Winchester_NC10_Eng.indb 4
2008-09-20 오후 1:36:32
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
3. Disassembly and Reassembly
Part
Picture
Description
17. Separate the Top Ass'y from the LCD.
18. Remove the Screw which ixes the SIM Card Sub-board
and the Main-Board, and then separate them.
M2 X L4, Black (2EA)
Main
System
19. Remove the Screw (3 EA) which connects the RHE and
the Main board and separate them.
M2 X L4, Black (3EA)
20. Remove the RHE as shown in the picture.
NC10
3-5
Winchester_NC10_Eng.indb 5
2008-09-20 오후 1:36:41
Plik z chomika:
picuall
Inne pliki z tego folderu:
samsung nc10.pdf
(15393 KB)
Inne foldery tego chomika:
Acer
Acorn
Aopen
Apple
Arima
Zgłoś jeśli
naruszono regulamin