tbd.pdf

(534 KB) Pobierz
679902636 UNPDF
TORPEDO PLANE
Plans for a realistic flying scale
model of the formidable Douglas
TBD-1
The structure is quite complete; workable flaps
and control surfaces are included to make the
model unusually interesting.
BY Alan D. Booton
The real ship bedecked in service
insignia. Details of the canopy are
interesting.
The wings of the TBD-1 fold upward to
facilitate stowage aboard aircraft
carriers.
Left -- The
completed model.
Note the depressed
flaps. Right -- The
units are easily
assembled. Wing is
one piece.
THE TBD-1 is a torpedo-bomber designed
for aircraft carrier service. Larger than the scout
or pursuit job, the TBD-1 has wings of unique
design, folding about midway on each span,
conserving space, which is limited on carriers.
An exceptionally high speed is obtained from the
850 h.p. Twin Wasp.
The folding wings, flaps, and realistic
movable controls have been included in the
model without a noticeable increase in weight,
and the accurate design has further possibilities
where more detail is desired. The simple method
of placing the wing eliminates the tedious line-up
job.
FUSELAGE
The formers can all be cut from a sheet 4
x 6" of 1/16" balsa plywood. Use waxed paper
between drawing and assemblies.
Build the left side of the fuselage on the
drawing and then build the right half directly to
the left half. Begin by pinning corresponding top
679902636.007.png 679902636.008.png 679902636.009.png 679902636.010.png 679902636.001.png 679902636.002.png
and bottom parts to the drawing and then
cement the formers to their respective stations. It
will be noticed there is nothing to cement to at
the top from A to E, so a 1/16" temporary strip is
cemented above the former spacers from A to D,
then up to E to aid assembly. The plain rib at the
bottom may be lightly cemented to, for the joints
are easily separated with a razor blade at the
proper time.
Add the balsa side longerons. Prebend
them to avoid a sprung fuselage. Remove from
board and duplicate the first steps right on the
assembled half, then add the bamboo stringers,
rear hook.
Bevel the three propeller blocks as shown
on the drawing and prime the bevels copiously
with cement. Before the priming has fully dried,
add more cement and clamp them together with
pins, on a flat surface. After drying several hours,
blank and carve each blade in the accepted
manner. Dope and sand to a glossy finish. The
balance may be obtained by adding a coat of
dope to the light blade. Assemble the prop, nose
plug, washers, and prop shaft.
COMPLETING THE MODEL
Cover the leading edge of the wing with
1/64” sheet balsa and the remainder with silver
tissue. Form the celluloid cockpit cover to fit well,
then remove it and cover as much of the
fuselage as possible. Cover the tail surfaces with
silver tissue. Install the wing in its place under
the fuselage. Slice through formers H and I on
lines directly over and between the second top
longerons. The top of the fuselage can then be
raised enough to install the stabilizer. Cement
the parts back together and cement the vertical
tail on. Check repeatedly to see that the surfaces
are in correct alignment. Fashion a dummy tail
wheel and deck hook and cement them in place.
Fillet the tail surfaces and wing with tissue.
Cement the cowling on, the cockpit cover and
radio antenna masts. Make the panel frames on
the cover by doping on narrow strips of silver
tissue.
Spray the tissue lightly with water and
when dry, if the model is streaky, coat the
surfaces with a thin coat of silver dope. The
wheels and inside the cowl are black. The
lettering is black. Add any remaining detail that is
desired.
Power the model with three loops of 1/8"
flat rubber. The loops are tied at both ends, the
special "S" look at the rear. The motor is
engaged to the rear hook by “fishing."
With this model, first tests should be
made by letting it take off finder its own power,
making adjustments between flights until a steep
left-hand climbing turn is accomplished.
WING AND LANDING GEAR
Build the wing as a unit. Due to the curve
of the ribs, the bottom spars must be blocked up
proportionately from root to tips to keep the
incidence even. Do not cut the ribs for the
ailerons until the wing is assembled, then slice
out for the aileron spars and fit the spars in.
Remove the top spar between the #2 ribs, then
crack all spars at #2 ribs and block the tips up 1-
7/8”. Replace the piece of top spar and cement
the cracked spars. When dry, remove and install
the flaps.
Cement the M pieces between ribs 3 and
4 and install the landing gear, which is explained
on the drawing.
TAIL SURFACES
Build the tail surfaces out of plain
unshaped stock, and when complete sand them
to the tapered streamlined shapes. This method
is much easier and more accurate than
precutting all ribs before assembly. The hinges
can be copper or soft iron wire. The lower part of
the rudder has to be added on to, to conform to
the last former. The stabilizer should be made as
a unit.
PROPELLER AND COWL
Carve and hollow the cowl from a soft
block and cement in the retainer disc. Make the
nose plug to fit snugly in the hole.
LIST OF MATERIALS
Blocks
1 1-3/4 x 2-1/8 x 2-1/8"
3 1-1/8 x 1-1/8 x 3-1/2"
2 1/2 x 1-3/8 x 1-3/8" or
1 pr. 1-3/8" air wheels
Sheet
1 1/8 x 2 x 12"
4 1/32 x 2 x 18”
2 1/16 x 2 x 18"
3 1/64 x 2 x 18"
Strips
2 1/8 sq. x 18"
12 1/16 sq. x 18"
4 3/32 sq. x 18"
Miscellaneous
10 ¢ tube
model airplane cement
1 oz.
clear dope
1/2 oz.
silver dope
2 sheets
silver tissue
2
spoiled negatives
2
bamboo sticks
24"
# 12 music wire
6 ft.
1/8" flat rubber
several
friction washers
Scanned From August 1938
Air Trails
679902636.003.png 679902636.004.png
679902636.005.png
679902636.006.png
Zgłoś jeśli naruszono regulamin