stosser.pdf
(
361 KB
)
Pobierz
FOCKE - WULF STOSSER
FOCKE - WULF STOSSER
Complete plans and directions for building a high performance miniature of
a world-famous German sportster.
By PAUL PLECAN and ROGER HAMMER
The framework of the model is distinctive. Master
stringers make fuselage construction simple. The
nose block and sturdy landing gear legs make a
sturdy ship. Note the position of the stabilizer.
When covered, the model becomes difficult to
distinguish from the real ship. The parasol
arrangement affords a really stable job. The
sweepback increases longitudinal and
directional stability.
Any model builder who has looked for a
model that was one hundred percent scale and
yet stable enough for flight with the scale tail
surfaces, will know how rare such a model is.
The Focke-Wulf Stosser fills the bill. Scale
outlines of the tail surfaces are shown on the
plans, as they have been proven to be of
sufficient size for a stable flying model.
Used mainly for training purposes, the
Stosser mounts an Argus inverted V-6 engine
which gives it a top speed of 167 miles per hour.
The cruising speed is 154 m.p.h., and the
landing speed is 56 m.p.h. The Stosser is a
familiar sight to many, as it was brought over by
Gerd Acheglis for participation in the acrobatic
events at the past few National Air Races. The
plans reproduced on the next few pages will
produce an accurate model of Gerd Acheglis'
original ship, that is, if they are followed
explicitly.
the whole unit for alignment, as some of the
master stringers are bound to be slightly warped.
The tail hook -- tail skid may be bent to shape
and cemented in place now, as there are no
stringers to impede your work. After this has
been done, cement the 1/16" square stringers in
their respective places. .Check again for
alignment, and correct if any warps are apparent.
Trace the side view of the engine nacelle (or
cowl) on a soft balsa block measuring 2 x 2-1/8 x
3". After shaping to conform with the side view,
repeat the process for the top view. Cut down
the outside of the cowl to the correct
cross-section and sand until smooth. Apply dope
(wood filler is better for this if it is available) and
sand very smooth when dry.
The cowl should be cut in half now, and
hollowed out to the thicknesses shown on the
plans. Cement together, and conceal the saw
mark where the cowl was cut in half by applying
successive coats of dope and sanding. The nose
plug can also be made at this time, and care
should be taken to have it fit quite snugly, as
adjustments are easier this way. The front
portion should be of very hard balsa, as it will
take a lot of abuse. Cement the two parts
together and add the two washers. (Note the
FUSELAGE
Since the fuselage is the toughest part, let
us tackle it first. Cut out the master stringers and
formers. Before proceeding any further, note that
there are two notches in the tail end of each side
master stringer. Mark off the positions of all the
formers on each master stringer, and cut the
grooves in the formers. After assembling, check
slight right thrust and larger amount of down
thrust.)
The landing-gear struts should be bent to
shape and cemented to the fuselage. The front
wire strut is bent back at the bottom to provide
an axle for the 1-1/4" balsa wheel. Cut the balsa
strut to the right size and insert between the two
wire struts, cementing well. The fuselage
covering maybe applied now, in small strips. Do
not forget to add piece "A" to the tops of formers
6 and 7, as it supports the stabilizer. The fillet
block in front of former 6 should be carved now
and cemented in place, and the whole unit
doped, since this will be harder when all the
struts and details have been added. The
fuselage is doped silver with two or three coats
of dope, and set aside. After it has dried well,
lettering and exhaust stacks may be added.
TAIL SURFACES
The tail surfaces are made in a way that
provides extreme flexibility and consequently
easier adjustments. The rudder and stabilizer are
broth cut from 1/16 x 3" sheet, and care is taken
to have the grain running the right way, as
shown on the plans. After the stabilizer has been
covered, the small fins shown in the side view
should be cemented on. The rudder should also
be covered, and both the parts doped silver. The
easiest way of duplicating the insignia shown on
the rudder is as follows: Dope a red band around
the rudder and set aside. While the red dope is
drying, cut a small circle from white bond paper.
On this paper draw the swastika and fill in with
black india ink. Cement the paper circle on the
middle of the red band-and there you are, a very
neat job done with a minimum of effort and time.
WING
Cut the ribs out of 1/16" sheet, making
two of each, except #3, of which fourteen should
be cut out. The 1/16" thick wing spar should be
cut to the depths shown by the rib notches.
Assemble the wing on a flat surface, such as a
drawing board, and cement the parts together.
Break the leading and trailing edges at the
proper points, set at the right angle to secure 1-
1/4" dihedral, and cement. The whole wing can
be covered now and doped silver. Do not forget
to draw the letters on the wing at this point, as it
will be very hard to do the lettering if the struts
are in place.
ASSEMBLING
The easiest way to get the wing at the
right incidence and position is to cut a small
piece of scrap sheet to the outline formed by the
bottom of the wing and the top of the fuselage.
Pin this jig on the fuselage and then pin the wing
to the top of it. Fit the struts by the "cut and try"
method, and after they have been cut to the right
size and sanded to a streamlined shape, cement
them in place. After you have fitted all the struts,
take the pins out of the jig and remove it. Add
slight amounts of cement to the joints between
the struts and the wing until a small fillet forms.
This will not only enhance the appearance, but
will duplicate the streamlined fairings on the
original ship.
Cement the stabilizer onto part "A," and fit
the rudder so that it will turn the model to the
right when gliding. Cut the propeller from a
medium block, of the size shown on the plan,
and carve so that it has about 3/32" or 1/8"
under-camber. Add the two half cones to the
side of the prop and then the top cone. The
freewheeling shown may be used, but this is
entirely up to the model builder. Add the small
details, such as the step on the left side of the
ship and the "N" strut between the main struts
and the bottom of the wing. The aileron and
rudder outlines can be simulated with a narrow
strip of black tissue cemented or doped over the
finished wing.
Since the entire model will weigh between
.7 and .9 ounce (depending on the materials
used, of course), four strands of 1/8" flat rubber
will do for normal flight. When lubricated, with an
inch of slack, the rubber can be wound up to 750
turns without fear of breakage. If you are in
doubt as to the freshness of the rubber,
however, do not use more than 600 turns.
Testing can best be accomplished on a grass-
covered field or lawn, but if you are a "city
slicker" you'll have to R.O.G. your model with
successively larger amounts of turns in it for
adjustments.
Scanned From November 1938
Air Trails
Plik z chomika:
arooo71
Inne pliki z tego folderu:
HURRI_1.BMP
(836 KB)
a5m2aclaude.tif
(539 KB)
Heinkel Pursuit.pdf
(402 KB)
Fokker d8 p5.gif
(105 KB)
luton_minor.pdf
(76 KB)
Inne foldery tego chomika:
Modele
Modele(1)
Modele(11)
Modele(12)
Modele(13)
Zgłoś jeśli
naruszono regulamin