Alignment & Adjustment.pdf

(638 KB) Pobierz
648662813 UNPDF
Adjustment
5. Adjustment
5-1 Basic guide for adjustment
■ After you replace the electronic parts, you must make adjustments for each adjustment item in ES60.
■ The following table shows the necessary adjustment item for replacing each part.
1. After replacing the electronic part, you must make adjustments for each item by referring to the following table.
<Table 5-1>
MAIN
PCB
POWER
PCB
BARREL
ASSY
CCD
ASSY
FIRMWARE UPGRADE
●
●
PUNT ADJ
●
● ●
SHUTTER CLOSE TIME, OB, LENS SHADING
●
● ●
FLASH ADJ
●  ●
BATTERY LEVEL ADJ
●  ●
BURNING TEST & CCD DEFECT CELL
●  ● ● ●
HORIZENTAL LINE ADJ
●
EEPROM READ
EEPROM WRITE
2. Adjustment equipment
- AE TESTER: AE TESTER that enables LV 12
  - Ininity Callimator for PUNT adjustment
- Gray chart (18%) for FLASH & AWB, DARK BOX)
- POWER SUPPLY: 4.2V/2A
3. Adjustment program ile
Save and use the program for each adjustment item on the SD card to adjust each item.
  The ile name for each adjustment item is the same as  “mondrian_123L_adj.txt” .
SAMSUNG
This Document can not be used without Samsung’s authorization
5-1
648662813.029.png 648662813.030.png 648662813.031.png 648662813.032.png 648662813.001.png 648662813.002.png 648662813.003.png 648662813.004.png 648662813.005.png 648662813.006.png 648662813.007.png 648662813.008.png 648662813.009.png
Adjustment
4. Operating procedure of adjustment program
Insert Flash Card (SD card) by process
Power On (Worker)
Auto process to Test Mode/Execute
adjustment script
Yes
Check process ID
No
Check by process
Display last process
ID executed normally
Record log ile by process 
(If necessary
Yes
Pass/No pass
No
Save adjustment value to EEPROM
Save adjustment value to
EEPROM (If necessary)
Display adjusted value and whether
it is OK (LCD)-
Display adjusted value and whether
it is OK (LCD)
Set process ID (EEPROM)
Auto Power Off or continue
with process
Power Off or stand by
5-2
This Document can not be used without Samsung's authorization
SAMSUNG
648662813.010.png 648662813.011.png 648662813.012.png 648662813.013.png 648662813.014.png 648662813.015.png 648662813.016.png 648662813.017.png 648662813.018.png 648662813.019.png
 
Adjustment
5-2 Lens Shading
■ Make adjustments to the Lens Shading to the surrounding brightness of each camera.
■ Because the surrounding brightness is lower compared to the center for each set, separately adjust each set
so that the surrounding brightness is higher.
<Adjustment method>
1. Prepare the AE TESTER.
  * Luminance speciication of the Light box is 12LV .
* The Light box is located at 10mm+-1mm with the body tube open.
  * The color temperature speciication of the Light box is  3300K .
2. Save the applicable adjustment ile to the SD card.
3. After inserting the SD card containing the program ile to the camera, set the camera to the AE TESTER.
Light source box
Camera
Fig. 5-1
4. Adjust the LV value of the AE METER to 12.
5. When you turn on the power of the camera, the adjustment will start automatically.
q Adjust the Lens Shading with large lense, Zoom 0 condition.
w Refer to the EEPROM WRITE information and write the adjustment result to EEPROM.
e Refer to the CARD WRITE INFORMATION to write the adjustment result to the data ile.
r Set the lower and upper speciication.
6. When the adjustment is completed, the camera will automatically be turned off.
<Adjustment result>
Open and check the CSV ile generated from the adjustment memory card.
SAMSUNG
This Document can not be used without Samsung’s authorization
5-3
648662813.020.png 648662813.021.png 648662813.022.png
Adjustment
5-3 Shutter Close Time ADJ
■ Adjust the Close timing of the device shutter by camera.
■ Because there is a deviation of shutter closing time by each set, make adjustments by each set to reduce this deviation.
■ AWB LOW item and AWB LOW are adjusted simultaneously.
<Adjustment method>
1. Prepare the AE TESTER that can be adjusted to LV 12 .
2. Install the camera to the AE TESTER.
  * Luminance speciication of the Light box is  12LV .
  * The color temperature speciication of the Light box is  3300K .
Light source box
Camera
Fig. 5-2
3. After inserting the SD card containing the program ile to the camera, turn on the power of the camera.
4. The adjustment process will automatically start.
q Refer to the speciication (Illiminance) for testing.
    -Line delay and Sub delay are adjusted so that the appropriate value can be identiied to the speciication illuminance.
w If the result line delay wis within the min and max range, it is OK. If it is outside of the range, process as NG.
e Refer to the EEPROM WRITE information and write the adjustment result to EEPROM.
r Refer to the CARD WRITE INFORMATION to write the adjustment result to the data ile.
5. When the adjustment is completed, the camera will automatically be turned off.
<Adjustment result>
Open and check the CSV ile generated from the adjustment memory card.
5-4
This Document can not be used without Samsung's authorization
SAMSUNG
648662813.023.png 648662813.024.png 648662813.025.png
Adjustment
5-4 CCD Gain ADJ
■ Because there is a deviation of CCD saturation level by each CCD, make adjustments to the basic analog gain to reduce this
deviation.
<Adjustment method>
1. Prepare the AE TESTER.
  * Luminance speciication of the Light box is  12LV .
* The Light box is located at 10mm+-1mm with the body tube open.
  * The color temperature speciication of the Light box is  3300K .
2. Save the applicable adjustment ile to the SD card.
3. After inserting the SD card containing the program ile to the camera, set the camera to the AE TESTER.
Light source box
Camera
Fig. 5-3
4. Adjust the LV value of the AE METER to 12 .
5. When you turn on the power of the camera, the adjustment will start automatically.
q Adjust the Gain.
w Refer to the EEPROM WRITE information and write the adjustment result to EEPROM.
e Refer to the CARD WRITE INFORMATION to write the adjustment result to the data ile.
r Set the lower and upper speciication.
6. When the adjustment is completed, the camera will automatically be turned off.
<Adjustment result>
Open and check the CSV ile generated from the adjustment memory card.
SAMSUNG
This Document can not be used without Samsung’s authorization
5-5
648662813.026.png 648662813.027.png 648662813.028.png
Zgłoś jeśli naruszono regulamin