Emulex.pdf

(350 KB) Pobierz
&DQRQ
Emulex
Quick Installation
Guide
TCP/IP Installation
Page 1
Novell NetWare 4.x Installation
Page 5
Novell NetWare 3.x Installation
·
Page 8
PCONSOLE Method
·
Network Printer Manager Method
Notes:
·
The procedures described below are tested with a ‘new from box’ Emulex Printer Server. To erase
the previous configuration reset the Printer Server change the Jumper to the reset position. Then
power on the machine for about one minute. Power off again and change the jumper back to its
original position. Now the Printer Server is ready to use.
·
Some actions in these procedures require Supervisor or Administrator access rights.
Issued by Canon Europa N.V., Technical Service Support Division
© Canon Europa N.V. 1998
995102715.007.png
TCP/IP Installation
TCP/IP Installation
Assign IP address to Printer Server (Using ARP)
Note:
To assign an IP address, the workstation or host must be on the same LAN segment as
the printer server.
1.
Start a MS-DOS Window on the workstation.
2.
Verify IP address availability by entering:
ping ip_address
Enter the IP address that will be assigned to the printer server.
For example: ping 123.234.002.001
You should not receive a response. If a response is received, select another IP address with the
assistance of the network administrator.
3.
Assign the IP address by entering:
arp -s ip_address mac_addr
Enter the IP address that will be assigned to the printer server.
The MAC address is on the faceplate of the printer server or on the configuration printout.
For example: arp –s 123.234.002.001 00-00-C9-00-09-A3
4.
Reboot the printer (and therefore the Printer Server)
5.
Verify the IP address was assigned by entering:
ping ip_address
Enter the new IP address of the printer server in decimal dot notation.
For example: ping 123.234.002.001
A response should be received from the printer server.
6.
If the above mentioned steps didn’t give any results then try again starting with step 3.
Emulex Quick Installation Guide
Page 1
995102715.008.png
 
TCP/IP Installation
Connecting the Printer Driver to the Printer Server
1.
Start the Printer Driver Installation and install the driver to the local LPT1: port.
2.
Open the Printer Properties Window and select the Ports tab.
3.
Choose the Add Port button.
4.
Select the LPR Port. (If this one is not available the Microsoft TCP/IP Printing services need to
be installed).
5.
Click the New Port button and the “Add LPR compatible printer” window will appear.
Emulex Quick Installation Guide
Page 2
995102715.009.png 995102715.001.png 995102715.002.png
 
TCP/IP Installation
6.
Enter the IP address in the top field (address) and “PASSTHRU” in the bottom field (name)
7.
Click the OK button and the port will show up in the list.
8.
Switch to the General tab.
9.
Test the connection by pressing the Test Print button.
Install and configure the Network Printer Manager (Optional)
1.
Start the NPM Installation. (Emulex CD \Utils\Admin\Setup.exe)
2.
Use the Management Protocol Selection Tool to select the option “Manage Via TCP/IP”.
3.
Edit the HOSTS file that is located in the Admin directory of the Network Printer Manager.
Enter all TCP/IP devices that need to be controlled by the NPM.
The format should be:
# IP address
Name
158.10.123.45
Accounting
174.189.251.13
NPE0009A3
193.204.15.56
MyPrinter
Emulex Quick Installation Guide
Page 3
995102715.003.png 995102715.004.png 995102715.005.png
 
TCP/IP Installation
4.
Start the Network Printer Manager
5.
Use this tool to check and to fine-tune the configuration of the Network Interface Card.
Emulex Quick Installation Guide
Page 4
995102715.006.png
 

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin