1143.PDF

(78 KB) Pobierz
19-3894; Rev 3; 10/94
+5V/Programmable Low-Dropout
Voltage Regulator
_______________General Description
The MAX667 low-dropout, positive, linear voltage regu-
lator supplies up to 250mA of output current. With no
load, it has a typical quiescent current of 20µA. At
200mA of output current, the input/output voltage differ-
ential is typically 150mV. Other features include a low-
voltage detector to indicate power failure, as well as
early-warning and low-dropout detectors to indicate an
imminent loss of output voltage regulation. A shutdown
control disables the output and puts the circuit into a
low quiescent-current mode.
The MAX667 employs Dual Mode™ operation. One
mode uses internally trimmed feedback resistors to pro-
duce +5V. In the other mode, the output may be varied
from +1.3V to +16V by connecting two external resistors.
The MAX667 is a pin-compatible upgrade to the
MAX666 in most applications where the input voltages
are above +3.5V. Choose the MAX667 when high out-
put currents and/or low dropout voltages are desired,
as well as for improved performance at higher
temperatures.
________________________Applications
Battery-Powered Devices
Pagers and Radio Control Receivers
Portable Instruments
Solar-Powered Instruments
____________________________Features
©
350mV Max Dropout at 200mA
©
250mA Output Current
©
Normal Mode: 20µA Typ Quiescent Current
Shutdown Mode: 0.2µA Typ Quiescent Current
©
Low-Battery Detector
©
Fixed +5V (Min Component Count) or
Adjustable Output
©
+3.5V to +16.5V Input
©
Dropout Detector Output
©
10µF Output Capacitor
______________Ordering Information
PART
TEMP. RANGE
PIN-PACKAGE
MAX667CPA
0°C to +70°C
8 Plastic DIP
MAX667CSA
0°C to +70°C
8 SO
Dice *
MAX667C/D
0°C to +70°C
MAX667EPA
-40°C to +85°C
8 Plastic DIP
MAX667ESA
-40°C to +85°C
8 SO
MAX667MJA
-55°C to +125°C
8 CERDIP
* Contact factory for dice specifications.
__________Typical Operating Circuit
__________________Pin Configuration
TOP VIEW
+5V OUT
IN
OUT
C1
10 m F
+6.3V
BATTERY
DD
1
2
3
4
8
7
6
5
IN
LBO
SET
SHDN
MAX667
OUT
MAX667
LBI
GND
SET
GND
SHDN
DIP/SO
TM Dual Mode is a trademark of Maxim Integrated Products.
________________________________________________________________ Maxim Integrated Products
1
Call toll free 1-800-998-8800 for free samples or literature.
769509245.299.png 769509245.310.png 769509245.321.png 769509245.332.png 769509245.001.png 769509245.012.png 769509245.023.png 769509245.034.png 769509245.045.png 769509245.056.png 769509245.067.png 769509245.078.png 769509245.089.png 769509245.100.png 769509245.111.png 769509245.122.png 769509245.133.png 769509245.144.png 769509245.155.png 769509245.166.png 769509245.177.png 769509245.188.png 769509245.199.png 769509245.210.png 769509245.221.png 769509245.232.png 769509245.243.png 769509245.254.png 769509245.264.png 769509245.275.png 769509245.276.png 769509245.277.png 769509245.278.png 769509245.279.png 769509245.280.png 769509245.281.png 769509245.282.png 769509245.283.png 769509245.284.png 769509245.285.png 769509245.286.png 769509245.287.png 769509245.288.png 769509245.289.png 769509245.290.png
 
+5V/Programmable Low-Dropout
Voltage Regulator
ABSOLUTE MAXIMUM RATINGS
Input Supply Voltage ...........................................................+18V
Output Short Circuited to Ground.........................................1sec
LBO Output Sink Current ....................................................50mA
LBO Output Voltage ...............................................GND to VOUT
SHDN Input Voltage ....................................-0.3V to (VIN + 0.3V)
Input Voltages LBI, SET................................-0.3V to (VIN - 1.0V)
Continuous Power Dissipation
Plastic DIP (derate 9.09mW/°C above +70°C) ............727mW
SO (derate 5.88mW/°C above +70°C) .........................471mW
CERDIP (derate 8.00mW/°C above +70°C) .................640mW
Operating Temperature Ranges
MAX667C_A........................................................0°C to +70°C
MAX667E_A .....................................................-40°C to +85°C
MAX667MJA ..................................................-55°C to +125°C
Storage Temperature Range .............................-65°C to +160°C
Lead Temperature (soldering, 10sec) .............................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(GND = 0V, V IN = +9V, V OUT = +5V, C1 = 10
m
F, unless otherwise noted.)
T A = +25°C
A = T MIN to T MAX
MIN
PARAMETER
SYMBOL
CONDITIONS
UNITS
MIN
TYP
MAX
TYP
MAX
Input Voltage
V IN
3.5
16.5
V
V SET = 0V, V IN = 6V, I OUT = 10mA,
T A = -40°C to +85°C
5
4.8
5.2
Output Voltage
V OUT
V
V SET = 0V, V IN = 6V, I OUT = 10mA,
T A = -55°C to +125°C
5
4.75
5.25
Maximum Output Current
I OUT
V IN = 6V, 4.5V < V OUT < 5.5V
250
250
mA
V SHDN = 2V
0.2
1
2
I OUT = 0µA
20
25
35
µA
Quiescent Current
I Q
V SHDN = 0V,
V SET = 0V
I OUT = 100µA
20
30
50
I OUT = 200mA
5 5
20
mA
I OUT = 100µA
5 0
75
Dropout Voltage (Note1)
mV
I OUT = 200mA
I OUT = 10mA to 200mA
150
250
350
Load Regulation
50
100
250
mV
Line Regulation
V IN = 6V to 10V, I OUT = 10mA
5 0
15
mV
SET Reference Voltage
V SET
1.225
1.20
1.25
V
SET Input Leakage Current
I SET
V SET = 1.5V
0.01
±10
±1000
nA
Output Leakage Current
I OUT
V SHDN = 2V
(Note 2)
0.1
1
µA
Short-Circuit Current
I OUT
400
450
mA
Low-Battery Detector
Reference Voltage
V LBI
1.225
1.195
1.255
V
Low-Battery Detector
Input Leakage Current
I LBI
V LBI = 1.5V
0.01
±10
±1000
nA
Low-Battery Detector
Output Voltage
V LBO
V IN = 9V, V LBI = 2V, I LBO = 10mA
V IH
0.25
0.4
V
1.5
1.5
SHDN Threshold
V SHDN
V
V IL
0.3
0.3
SHDN Leakage Current
I SHDN
V SHDN = 0V to V IN
0.01
±10
±1000
nA
V SET = 0V,
V SHDN = 0V,
R DD = 100k
V IN = 7V
0.25
Dropout Detector Output
Voltage
V DD
V
½
,
V IN = 4.5V
3.5
I OUT = 10mA
Note 1: Dropout Voltage is V IN -V OUT when V OUT falls to 0.1V below its value at V IN = V OUT + 2V.
Note 2: Short-Circuit Current is pulse tested to maintain junction temperature. Short-circuit duration is limited by package dissipation.
2
_______________________________________________________________________________________
769509245.291.png 769509245.292.png 769509245.293.png 769509245.294.png 769509245.295.png 769509245.296.png 769509245.297.png 769509245.298.png 769509245.300.png 769509245.301.png 769509245.302.png 769509245.303.png 769509245.304.png 769509245.305.png 769509245.306.png 769509245.307.png 769509245.308.png 769509245.309.png 769509245.311.png 769509245.312.png 769509245.313.png 769509245.314.png 769509245.315.png 769509245.316.png 769509245.317.png 769509245.318.png 769509245.319.png 769509245.320.png 769509245.322.png 769509245.323.png 769509245.324.png 769509245.325.png 769509245.326.png 769509245.327.png 769509245.328.png 769509245.329.png 769509245.330.png 769509245.331.png 769509245.333.png 769509245.334.png 769509245.335.png 769509245.336.png 769509245.337.png 769509245.338.png 769509245.339.png 769509245.340.png 769509245.341.png 769509245.342.png 769509245.002.png 769509245.003.png 769509245.004.png 769509245.005.png 769509245.006.png 769509245.007.png 769509245.008.png 769509245.009.png 769509245.010.png 769509245.011.png 769509245.013.png 769509245.014.png 769509245.015.png 769509245.016.png 769509245.017.png 769509245.018.png 769509245.019.png 769509245.020.png
+5V/Programmable Low-Dropout
Voltage Regulator
__________________________________________Typical Operating Characteristics
(T A = +25°C, unless otherwise noted.)
QUIESCENT CURRENT
vs. LOAD CURRENT
DROPOUT VOLTAGE
vs. LOAD CURRENT
DD OUTPUT CURRENT
vs. INPUT-OUTPUT DIFFERENCE
1000
1000
100,000
V IN = +6V
5 10
20 50 100mA LOAD
10,000
100
100
1000
10
10
100
1
2
10
1
1
0.01
0.1
1
10
100
1000
1
10
100
1000
0
50
100
150
200
250
LOAD CURRENT (mA)
LOAD CURRENT (mA)
INPUT-OUTPUT DIFFERENCE (mV)
_____________________Pin Description
_______________Detailed Description
Figure 1 shows a micropower bandgap reference, an
error amplifier, a PNP pass transistor, and two com-
parators as the main elements of the MAX667. One
comparator, C1, selects the fixed 5V or adjustable
operation with an external voltage divider. The other
comparator, C2, is a low-battery detector.
The bandgap reference, which is trimmed to 1.22V,
connects internally to one input of the error amplifier,
A1. The feedback signal from the regulator output sup-
plies the other input of A1 from either an on-chip volt-
age divider or two external resistors. When SET is
grounded, the internal divider provides the error ampli-
fier feedback signal for a fixed 5V output. When SET is
more than 50mV above ground, the error amplifier’s
input switches directly to SET while an external resistor
divider from OUT determines the output voltage.
A second comparator, C2, compares the LBI input to
the internal reference voltage. LBO is an open-drain
FET connected to GND. The low-battery threshold can
also be set with a voltage divider at LBI. In addition, the
MAX667 has a shutdown input (SHDN) that disables
the load and the device while reducing quiescent cur-
rent when it is pulled high.
PIN
NAME
FUNCTION
Dropout Detector Output—the collec-
tor of a PNP pass transistor. Normally
an open circuit, it sources current as
dropout is reached.
1
DD
Regulated Output Voltage. OUT falls
to 0V when SHDN is above 1.5V. SET
determines output voltage when SET
is above 50mV; otherwise, it is 5V.
OUT must be connected to an output
filter capacitor.
2
OUT
Low-Battery Detector. A CMOS input
to an internal 1.255V comparator
whose output is the LBO pin.
3
LBI
4
GND
Ground
Shutdown Input. Connect to GND for
normal operation (output active). Pull
above 1.5V to disable OUT, LBO, and
DD and to reduce quiescent current to
less than 1µA.
5
SHDN
(Output) Voltage Set, CMOS Input.
Connect to GND for 5V output. For
other voltages, connect external resis-
tive divider from OUT.
6
SET
+5V Output
Figure 2 shows the connection for a fixed 5V output.
The SET input is grounded, and no external resistors
are required. Figure 3 shows adjustable output opera-
tion. R1 and R2 set the output voltage. SHDN should be
grounded if not used.
Low-Battery Output. An open-drain N-
channel transistor that sinks current to
GND when LBI is less than 1.22V.
7
LBO
8
IN
Positive Input Voltage (unregulated)
_______________________________________________________________________________________
3
769509245.021.png 769509245.022.png 769509245.024.png 769509245.025.png 769509245.026.png 769509245.027.png 769509245.028.png 769509245.029.png 769509245.030.png 769509245.031.png 769509245.032.png 769509245.033.png 769509245.035.png 769509245.036.png 769509245.037.png 769509245.038.png 769509245.039.png 769509245.040.png 769509245.041.png 769509245.042.png 769509245.043.png 769509245.044.png 769509245.046.png 769509245.047.png 769509245.048.png 769509245.049.png 769509245.050.png 769509245.051.png 769509245.052.png 769509245.053.png 769509245.054.png 769509245.055.png 769509245.057.png 769509245.058.png 769509245.059.png 769509245.060.png 769509245.061.png 769509245.062.png 769509245.063.png 769509245.064.png 769509245.065.png 769509245.066.png 769509245.068.png 769509245.069.png 769509245.070.png 769509245.071.png 769509245.072.png 769509245.073.png 769509245.074.png 769509245.075.png 769509245.076.png 769509245.077.png 769509245.079.png 769509245.080.png 769509245.081.png 769509245.082.png 769509245.083.png 769509245.084.png 769509245.085.png 769509245.086.png 769509245.087.png 769509245.088.png 769509245.090.png 769509245.091.png 769509245.092.png 769509245.093.png 769509245.094.png
+5V/Programmable Low-Dropout
Voltage Regulator
IN
OUT
DD
SHDN
A1
SET
LBO
C2
C1
1.255V REF
LBI
+50mV
GND
MAX667
Figure 1. MAX667 Block Diagram
MAX667
V OUT
8
2
IN
LBO
OUT
8
2
+5V OUT
250mA
IN
OUT
C1
10
7
C1
10
m
F
m
F
N
VREF
MAX667
R3
R2
LBI
3
6
SET
SET
GND
SHDN
6
4
5
R4
R1
SHDN
GND
5
4
Figure 2. Fixed +5V Regulator
Figure 3. Adjustable Output and Low-Battery Detector
4
_______________________________________________________________________________________
769509245.095.png 769509245.096.png 769509245.097.png 769509245.098.png 769509245.099.png 769509245.101.png 769509245.102.png 769509245.103.png 769509245.104.png 769509245.105.png 769509245.106.png 769509245.107.png 769509245.108.png 769509245.109.png 769509245.110.png 769509245.112.png 769509245.113.png 769509245.114.png 769509245.115.png 769509245.116.png 769509245.117.png 769509245.118.png 769509245.119.png 769509245.120.png 769509245.121.png 769509245.123.png 769509245.124.png 769509245.125.png 769509245.126.png 769509245.127.png 769509245.128.png 769509245.129.png 769509245.130.png 769509245.131.png 769509245.132.png 769509245.134.png 769509245.135.png 769509245.136.png 769509245.137.png 769509245.138.png 769509245.139.png 769509245.140.png 769509245.141.png 769509245.142.png 769509245.143.png 769509245.145.png 769509245.146.png 769509245.147.png 769509245.148.png 769509245.149.png 769509245.150.png 769509245.151.png 769509245.152.png 769509245.153.png 769509245.154.png 769509245.156.png 769509245.157.png 769509245.158.png 769509245.159.png 769509245.160.png 769509245.161.png 769509245.162.png 769509245.163.png 769509245.164.png 769509245.165.png 769509245.167.png 769509245.168.png 769509245.169.png 769509245.170.png 769509245.171.png 769509245.172.png 769509245.173.png 769509245.174.png 769509245.175.png 769509245.176.png 769509245.178.png 769509245.179.png 769509245.180.png 769509245.181.png 769509245.182.png 769509245.183.png 769509245.184.png 769509245.185.png 769509245.186.png 769509245.187.png 769509245.189.png 769509245.190.png 769509245.191.png 769509245.192.png 769509245.193.png 769509245.194.png 769509245.195.png 769509245.196.png 769509245.197.png 769509245.198.png 769509245.200.png 769509245.201.png 769509245.202.png 769509245.203.png 769509245.204.png 769509245.205.png 769509245.206.png 769509245.207.png 769509245.208.png 769509245.209.png 769509245.211.png 769509245.212.png 769509245.213.png 769509245.214.png 769509245.215.png 769509245.216.png 769509245.217.png 769509245.218.png 769509245.219.png 769509245.220.png 769509245.222.png 769509245.223.png 769509245.224.png 769509245.225.png 769509245.226.png 769509245.227.png 769509245.228.png 769509245.229.png 769509245.230.png 769509245.231.png 769509245.233.png 769509245.234.png 769509245.235.png 769509245.236.png 769509245.237.png 769509245.238.png 769509245.239.png 769509245.240.png 769509245.241.png 769509245.242.png 769509245.244.png 769509245.245.png 769509245.246.png 769509245.247.png 769509245.248.png 769509245.249.png 769509245.250.png 769509245.251.png 769509245.252.png 769509245.253.png 769509245.255.png 769509245.256.png 769509245.257.png
 
+5V/Programmable Low-Dropout
Voltage Regulator
Output-Voltage Selection
If SET is connected to a resistive voltage divider (Figure
3), the output voltage is set by the equation:
V OUT = V SET x (R1 + R2) / R1,
where V SET = 1.22V
To simplify resistor selection:
R2 = R1 x (V OUT / V SET - 1)
Since the input bias current at SET has a maximum
value of 10nA, relatively large values can be used for
R1 and R2 with no loss of accuracy. 1M ½ is a typical
value for R1. The V SET tolerance is less than ±25mV.
This allows the output to be preset without trim pots,
using only fixed resistors in most cases. However,
when resistor values greater than 1M ½ are used, pay
special attention to printed circuit board leakage that
can introduce error at the SET input.
Shutdown (Standby) Mode
SHDN puts the device into standby mode to conserve
power. When this pin is held low, the IC operates nor-
mally. If it is driven above 1.5V, the chip shuts down.
Quiescent current of the MAX667 is then reduced to
less than 1µA, and OUT turns off.
Note that the voltage for SHDN must never be more
than 0.3V higher than V IN .
Dropout Detector
The minimum input-output differential, or dropout volt-
age, determines the regulator’s lowest usable input
voltage. In battery-operated systems, this determines
the useful end-of-life battery voltage. The MAX667 fea-
tures very low dropout voltage (see Electrical
Characteristics). In addition, the MAX667 has a dropout
detector output, DD, that changes as the dropout volt-
age approaches its limit. DD is an open collector of a
PNP transistor. The dropout voltage and the dropout
detector both depend on the output current and tem-
perature. When the input voltage is more than 300mV
above the output voltage, the dropout detector will not
conduct. As the differential decreases below 300mV,
the DD source current increases abruptly. This current
signals a warning that regulation is about to be lost.
Connecting a resistor (typically 100k ½ ) from DD to
ground develops a voltage that can be monitored by
analog circuits or changed to digital levels by a com-
parator. LBI may be used for this purpose.
__________Applications Information
Output Capacitor
As with all PNP output regulators, an output capacitor
(C1, Figure 2) is required to maintain stability. 10
F is
recommended. To ensure stability, the output-capacitor
ESR must be sufficiently high. Figure 4 shows the mini-
mum required output-capacitor ESR for a given temper-
ature. Alternatively, a resistor may be added in series
with the output capacitor (Figure 5); the sum of the out-
m
Low-Battery Function
The MAX667 contains circuitry for low-battery detec-
tion. If the voltage at LBI falls below the regulator’s
internal reference (1.22V), LBO, an open-drain output,
sinks current to GND. The threshold can be set to any
level above the reference voltage by connecting a
resistive divider to LBI based on the equation:
R3 = R4 x (V BATT / V LBI - 1)
where V BATT is the desired threshold of the low-battery
detector, and R3 and R4 are the LBI input divider
resistors.
Since LBI input current is no more than 10nA, high val-
ues for R3 and R4 minimize loading. If V OUT is 5V, a
5.5V low-battery threshold can be set using 8.2M
5
4
3
2
½
for
R3 and 2.4M
½
for R4. When resistor values greater
than 1M
are used, pay special attention to PC board
leakage that can introduce error at the LBI input.
When the voltage at LBI is below the internal threshold,
LBO sinks current to GND. A pull-up resistor of 10k
½
1
0
or
more connected to OUT can be used with this pin when
driving CMOS circuits. Any pull-up resistor connected
to LBO should not be returned to a voltage source
greater than V OUT . When LBI is above the threshold or
the MAX667 is in SHDN mode, the LBO output is off.
½
-60
-40 -20
0
20
40
60
80
100 120
TEMPERATURE (˚C)
Figure 4. Minimum Required Output-Capacitor ESR vs.
Temperature
_______________________________________________________________________________________
5
769509245.258.png 769509245.259.png 769509245.260.png 769509245.261.png 769509245.262.png 769509245.263.png 769509245.265.png 769509245.266.png 769509245.267.png 769509245.268.png 769509245.269.png 769509245.270.png 769509245.271.png 769509245.272.png 769509245.273.png 769509245.274.png
 
Zgłoś jeśli naruszono regulamin