Title=English ------------------------------------------ 1001=Select 1002=Make 1003=Model/Version 1004=System 1005=ECU 1006=Connect 1007=Auto/Cn 1008=Settings 1009=There is a new version of the program at 1010=Scan 1011=Send Report 1050=Connecting... 1051=CONNECTING TO ECU 1052=Please Wait 1053=The key must be ON. Press ESC To Abort 1054=Invalid ISO Code 1055=Press Y To Continue or Press N To Abort 1056=CONNECTION FAILED 1057=Check your cable and serial port settings! 1058=Disconnected 1059=Press Y to continue 1060=Latency Too High!!! 1061=You need ELM 327/OBDKey interface to connect to this module! 1062=You need K-Line/VagCom/OBDKey interface to connect to this module! 1070=WARNING 1071=The running time of free version is limited to 20 minutes. The program will close in 1 minute! 1072=The running time of free version is limited to 20 minutes. The program will now close! 1073=You may select up to 4 parameters in the FREE version! 1074=Please UNPLUG OBDKey from OBD connector. 1075=Then PLUG OBDKey back and press Y in 10 seconds. 1076=SEND DIAGNOSTIC REPORT 1077=Diagnostic report of your last session will be sent to FiatECUScan server. 1078=The report is ANONYMOUS and does not contain any personal data! Continue? Press Y or N 1079=SENDING DIAGNOSTIC REPORT 1080=SENDING FAILED 1101=Engine 1102=ABS 1103=Airbag 1104=Electric Steering 1105=Gearbox 1106=Dashboard 1107=Body 1108=Service 1109=Headlights 1110=Climate control 1111=Other 1112=CAN ------------------------------------------ 2001=Info 2002=Disconnect 2003=WARNING: Invalid ISO code for selected vehicle system! ------------------------------------------ 3001=Errors 3002=Clear Errors 3003=No fault codes 3004=No fault codes detected by ECU 3050=CLEARING STORED FAULT CODES 3051=Light ON 3052=None 3053=Stored 3054=Intermittent 3055=Fatal 3056=Invalid signal 3057=No signal 3058=Signal low 3059=Signal high 3060=Impact occurred 3061=Intermittent 3062=Present 3065=The reason for this fault is that ECU has received invalid signal from the sensor. 3066=The reason for this fault is that ECU did not receive signal from the sensor. 3067=The reason for this fault is that ECU has received very low signal from the sensor. 3068=The reason for this fault is that ECU has received very high signal from the sensor. 3070=The reason for this fault is 3071=The current status of the fault is 3072=The error counter value is 3073=Dashboard warning light was not activated for this fault. 3074=Dashboard warning light was activated for this fault. 3075=The fault is not detected now. Clear fault codes, and observe for future appearance of the same fault. 3076=The fault is not detected now, but it is stored in memory. Clear fault codes, and observe for future appearance of the same fault. 3077=The fault is intermittent. Clear fault codes, and observe for future appearance of the same fault. 3078=The fault is present now. Take appropriate action to fix this sensor fault. 3080=Generic 3081=Open circuit 3082=Short circuit at ground 3083=Short circuit at +V batt 3084=Open circuit / Short circuit at ground 3085=Open circuit / Short circuit at +V batt 3086=Value too low 3087=Value too high 3088=Value constant 3089=Plausibility 3090=Short circuit 3091=Interference detected / Faulty signal 3092=Open circuit / No signal / Airbag impact 3093=Unknown / Pretensioners impact 3094=Unknown / Passenger airbag impact 3095=Unknown / Internal error 3096=Unknown / Driver airbag impact 3097=Unknown / Short circuit 3098=Unknown / No power supply 3099=Unknown ------------------------------------------ 4001=Parameters 4002=Selected Up 4003=Alpha sort 4004=Units sort 4005=Auto Up 4006=Load 4007=Save 4008=Add Template 4009=Templates 4101=Time %=% °C=°C bar=bar deg.=deg. deg./sec.=deg./sec. G=G gr/s=gr/s Kg/h=Kg/h km=km km/h=km/h m/s=m/s m/sec²=m/sec² mA=mA A=A mBar=mBar mg/i=mg/i Min=Min mm=mm mm³/i=mm³/i ms=ms mV=mV Nm=Nm rpm=rpm sec=sec steps=steps V=V days=days l/h=l/h ------------------------------------------ 5001=Graph 5002=Min 5003=Max 5004=File 5005=Start 5006=Stop 5007=Export 5008=Import 5020=Graphs 5021=Rate 5022=Scale 5030=Tags ------------------------------------------ 6001=Actuators 6002=Execute 6050=PLEASE READ ALL NOTES 6051=COMPLETED 6052=FAILED TO EXECUTE 6053=Incorrect conditions to run this test! 6054=Test NOT supported! 6055=Status: 6056=Status: UNKNOWN 6061=SECURITY CODE 6062=Invalid security code! 6063=WARNING: The Body Computer blocks for 30 min after 3 attempts! 6064=The Body Computer is blocked 6065=You must wait 30 minutes with key ON to unblock 6066=Security access failed 6067=Undefined error 6068=PREPARE REMOTE CONTROL {0} 6069=Press Y and you will have 15 seconds to press RC button 6070=Press N if you do not have any more remote controls 6071=DETECTING REMOTE CONTROL {0} 6072=Press any RC button for more than 3 seconds 6073=STORING REMOTE CONTROLS 6200=A/C SYSTEM RELAY ACTIVATION 6201=ACTIVATES THE BUZZER 6202=ACTUATES THE COIL 6203=ACTUATES EGR VALVE 6204=ACTUATES EVAP. PURGE VALVE 6205=ACTUATES IDLE ACTUATOR 6206=ACTUATES THE INJECTOR 6207=ACTUATES THE FUEL PUMP RELAY 6208=ACTUATES THE PUMP 6209=ACTUATES THE RELAY 6210=ACTUATES THE SOLENOID VALVE 6211=CHECK INDICATOR LIGHT ON 6212=EGR VALVE ACTIVATION 6213=FAST IDLE ACTIVATION 6214=GLOW PLUG LAMP ACTIVATION 6215=GLOW PLUG RELAY ACTIVATION 6216=HEATER RELAY ACTIVATION 6217=IN PROGRESS 6218=RUNS THE FAN AT HIGH SPEED 6219=RUNS THE FAN AT LOW SPEED 6220=TIMING ACTUATOR ACTIVATION 6221=VERIFY NEEDLE SHIFTING 6222=WARNING LAMP ACTIVATION 6223=WARNING LIGHT ACTIVATION 6224=WARNING LIGHT TEST ------------------------------------------ 7001=Adjustments 7002=Execute ------------------------------------------ 8001=Log 8101=Interface Type 8102=Serial Port 8103=Speed 8104=UI Language 8105=Data Language 8106=CSV Separator 8107=CSV Folder 8108=LOG Folder 8109=Play sounds 8111=Parameter Colors 8112=Background Color 8113=Grid Color 8114=Y-Axis Font 8115=X-Axis Font 8116=Parameter Font 8117=Line Thickness 8118=Change 8119=UI Font (Grids) 8120=UI Font (Buttons) 8121=Show available ports only 8191=Settings 8192=General 8193=Graph 8198=Cancel 8199=OK
HALUS12041985