Book Case 2.pdf

(1054 KB) Pobierz
112885485 UNPDF
67
BOOKCASE
Copyright 2004 Martian Auctions
314
112885485.011.png 112885485.012.png
Cutting the Parts
For precise crosscuts, first make a simple, self-aligning T-
guide for your circular saw. Cut a piece of 1/2-in. plywood to
2 1/2 x 24 in. and glue and screw it to a roughly 12-in.-long
piece of 1 x 4 pine that will serve as the crossbar of the T.
Center the plywood strip along the 1 x 4 and make sure the
pieces are perfectly square to each other.
Butt the crossbar of the T-guide against the edge of a piece
of scrap lumber, tack the guide in place and make a cut
through the 1 x 4 with your saw base guided by the plywood
strip. Then, trim the 1 x 4 on the opposite side in the same
way. Now, the ends of the 1 x 4 can be aligned with layout
lines on the stock for precise cut positioning.
Fig. 1 Mark the lengths of the bookcase side panels
on 1 x 10 lumber and use a square to lay out the
crosscut lines.
Begin construction by using a tape measure to mark the
length of a side panel on 1 x 10 stock, and lay out the cut
line with a square (Fig. 1) . The side panels on our bookcase
are 48 in. long.
Place the T-guide against the edge of the stock and align its
trimmed end with the cut line. Tack the guide in place and
use your circular saw to make the cut (Fig. 2) .
To support your work during the cuts, use 2 x 4s spanning
two saw-horses for a temporary bench and clamp your work
in place. Set your circular saw cutting depth so the blade
cuts about 1/8 in. into the 2 x 4s.
After both sides are cut to length, lay out and cut the five
shelves to length to suit the width of your bookcase. Our
shelf length is 31 in.
Fig. 2 With a T-guide cut to match your saw, align
the end of guide with crosscut line. Tack guide to the
work and then make the cut.
Rip the four lower shelves to 8 7/8 in. wide to allow for the
thickness of the case back. Clamp each shelf to the
sawhorses and tack a straight strip to the work to guide your
circular saw ( Fig. 3 ).
Next, cut the 10 shelf-support cleats from lengths of 1/2 x
3/4-in. parting strip. Use a handsaw to cut the pieces slightly
oversize, then gang the pieces together with masking tape.
Mark the cut lines and use your circular saw and T-guide to
cut the cleats to 8 7/8 in. long ( Fig. 4 ).
Because we varied the spaces between the shelves, the
vertical back cleat lengths vary. Rough cut and mark the
back cleats in pairs. From the top down, the lengths are 8,
9, 9 1/2 and 11 1/4 in. When cutting the back cleats with the
T-guide, first gang them together so all the marks on one
side align. After the cut, untape the cleats and reposition
them so the marks on the opposite side are aligned for the
next cut.
Fig. 3 Use a straight strip as a guide when ripping
stock for the four lower shelves to 8 7/8 in. The top
shelf remains a full 1 x 10.
315
Copyright 2004 Martian Auctions
112885485.013.png 112885485.014.png 112885485.001.png
Fig. 4 After cutting shelf cleats oversize, gang them
together with tape, mark the cut lines and trim with a
T-guide and circular saw.
Assembly
First mark the shelf cleat locations. Hook your tape
measure to the top edge of a side panel, extend the tape
and place marks at the following dimensions: 3/4, 10 1/4,
20 3/4, 31 3/4 and 44 1/2 in. These marks indicate the
top edges of the shelf cleats. Transfer the marks to the
other panel. Lay both side pieces edge to edge with the
marks on the outer edges and use a rule or straightedge
to extend the shelf locations across both panels at once
( Fig. 5 ).
Use 2d nails and glue to attach the shelf cleats to the sides.
Position the cleats so they're flush with the front edges of
the sides. Then, attach the vertical back cleats, leaving a
3/4-in. gap at the bottom of each back cleat for a shelf ( Fig.
6 ). The gaps will help to keep the shelves aligned during
assembly. Align the back cleats with the back ends of the
shelf cleats to provide the 3/8-in. recess for the back panel.
Fig. 5 Butt sides together with shelf-location marks
on outer edges. Use a straightedge to extend the
shelf marks across work.
Fig. 6 Nail and glue shelf cleats and back cleats to
the side panels. Note that cleats are recessed 3/8 in.
from back edge of sides.
Copyright 2004 Martian Auctions
316
112885485.002.png 112885485.003.png 112885485.004.png
To join the sides and shelves, first lay a side panel on a few
2 x 4s placed on the floor. With a helper assisting, stand the
shelves in position and lay the opposite side on the shelf
ends. Start a pair of 6d finishing nails at each shelf location
so the points just penetrate the shelves. Lift the side off and
apply glue to the endgrain of the shelves. Let the glue soak
in for a few minutes, then apply a second coat. Follow with
a coat of glue on the sides and cleats. Replace the panel
using the nail points to align the shelves. Then drive the
nails ( Fig. 7 ) and set them below the surface.
After the first side is attached, grasp the sides at one end
while your helper grasps the opposite end and flip the
assembly over. Secure the remaining side and check that
the case is square. If necessary, tack a diagonal brace
across the back to hold it while the glue sets. When the glue
is dry cut a piece of parting strip to fit between the two top
cleats and under the top shelf. This piece will be set 3/8 in.
in front of the top shelf rear edge to provide room for the
back panel. Glue and nail this long cleat to the shelf.
Fig. 7 Secure one side to the shelves with glue and
6d finishing nails. Then flip the assembly over and
attach the other side. Set all nails.
Adding the Fascia
To fit the 1 x 2 fascia over the case front edges, first mark
the stock for crosscutting. Make the vertical pieces 48 in.
long to match the sides and mark the horizontal members at
29 1/2 in. Rough cut the pieces to length and use the T-
guide and circular saw to trim them squarely to exact size.
Apply glue to one of the vertical members and nail it to the
case so its edge is flush with the side. Then, add each
horizontal member with glue and nails, keeping the top
edges flush with the shelf tops ( Fig. 8 ). Finally, add the
remaining vertical member with nails and glue.
Fig. 8 Attach the 1 x 2 strips to the case starting with
a vertical member. Then, add the horizontal pieces
and the other vertical.
Use 1 x 4 stock for the front and two side baseboard pieces.
Cut the length of each side piece to 10 in. long and glue
and nail the parts in place. Then, cut the front baseboard
piece to 34 in. long and secure it so its ends are flush with
the side pieces.
After the glue has dried, use a block plane to trim a chamfer
around the top edge of the baseboard. Plane the side
pieces first, working from front to back to avoid splitting the
corners of the front piece. Then, plane the front piece to
match. It helps to lean the plane against the case to
maintain a uniform angle ( Fig. 9 ).
The final component is the case back. Lay out the cut lines
on 1/4-in.-thick lauan plywood. Tack a straight strip to the
panel to serve as a guide for your circular saw and cut the
stock to size ( Fig. 10 ). Attach the back panels to the case
with glue and 1-in. finishing nails.
Fig. 9 Use a block plane to shape the chamfers on
the baseboard. Rest the plane against the case to
maintain a uniform angle.
Copyright 2004 Martian Auctions
317
112885485.005.png 112885485.006.png 112885485.007.png
Fig. 10 Cut the 1/4-in.-thick back panel to size with a
circular saw. Use a straight strip as a guide when
making the cuts.
Finishing
First make sure all the nails are set below the surface. Use
a putty knife to fill the nail holes with wood filler and let the
compound dry ( Fig. 11 ).
Sand the entire bookcase with 120- followed by 220-grit
sandpaper. Then, use a sanding block and 220-grit paper to
slightly ease all corners. Thoroughly dust off the case with a
tack rag.
If you plan to paint your bookcase, first apply two coats of
shellac over each knot to prevent the knots from bleeding
through the final paint job ( Fig. 12 ).
Fig. 11 Use a nail set to drive all nails below the
surface. Then apply wood filler over the nailheads
with a putty knife.
Then, prime and paint the bookcase according to the
manufacturer's instructions.
Fig. 12 Apply shellac to any knots before painting.
This will seal the knots and prevent sap from
bleeding through.
Copyright 2004 Martian Auctions
318
112885485.008.png 112885485.009.png 112885485.010.png
Zgłoś jeśli naruszono regulamin