osmesm_e.pdf
(
2338 KB
)
Pobierz
Preface,
Contents
SIMATIC NET
Introduction
1
Industrial Ethernet
OSM/ESM
Functions
2
Network Topologies with
OSM/ESM
3
Interfaces, Displays and
Operator Controls
4
Operating Instructions
Installation, Commissioning,
Cleaning and Maintenance
5
Firmware Update
6
Technical Specifications
7
Further Support
8
Notes on the CE Mark
9
Glossary
10
References
11
Index
12
Release 04/2002
C79000-Z8976-C068-07
Classification of Safety-Related Notices
This document contains notices which you should observe to ensure your own
personal safety, as well as to protect the product and connected equipment. These
notices are highlighted in the manual by a warning triangle and are marked as follows
according to the level of danger:
!
Danger
indicates that death or severe personal injury
will
result if proper precautions are not
taken.
!
Warning
indicates that death or severe personal injury
can
result if proper precautions are not
taken.
!
Caution
with warning triangle indicates that minor personal injury can result if proper
precautions are not taken.
Caution
without warning triangle indicates that damage to property can result if proper
precautions are not taken.
Notice
indicates that an undesirable result or status can occur if the relevant notice is
ignored.
Note
highlights important information on the product, using the product, or part of the
documentation that is of particular importance and that will be of benefit to the user.
Trademarks
SIMATIC
, SIMATIC NET
, SINEC
and SIMATIC NET Networking for Industry
®
are registered trademarks of Siemens AG.
Third parties using for their own purposes any other names in this document which
refer to trademarks might infringe upon the rights of the trademark owners.
Safety Instructions Regarding your Product
Before you use the product described here, read the safety instructions below
thoroughly.
Qualified Personnel
Only qualified personnel should be allowed to install and work on this equipment .
Qualified persons are defined as persons who are authorized to commission, to
ground, and to tag circuits, equipment, and systems in accordance with established
safety practices and standards.
Correct Usage of Hardware Products
Please note the following regarding the correct usage of hardware products:
Caution
This device and its components may only be used for the applications described in
the catalog or the technical description, and only in connection with devices or
components from other manufacturers which have been approved or recommended
by Siemens.
This product can only function correctly and safely if it is transported, stored, set up,
and installed correctly, and operated and maintained as recommended.
Before you use the supplied sample programs or programs you have written yourself,
make certain that no injury to persons nor damage to equipment can result in your
plant or process.
EU Directive: Do not start up until you have established that the machine on which
you intend to run this component complies with the directive 89/392/EEC.
Correct Usage of Software Products
Please note the following regarding the correct usage of software products:
Caution
This software may only be used for the applications described in the catalog or the
technical description, and only in connection with devices or software products from
other manufacturers which have been approved or recommended by Siemens.
Before you use the supplied sample programs or programs you have written yourself,
make certain that no injury to persons nor damage to equipment can result in your
plant or process.
Prior to Startup
Before putting the product into operation, note the following warning:
Caution
Prior to startup you must observe the instructions in the relevant documentation. For
ordering data of the documentation please refer to the catalogs or contact your local
SIEMENS representative.
Copyright Siemens AG 2000/02, All rights reserved
The reproduction, transmission or use of this document or its
contents is not permitted without express written authority.
Offenders will be liable for damages. All rights, including rights
created by patent grant or registration of a utility or design, are
reserved.
Disclaimer
We have checked the contents of this manual for agreement with
the hardware and software described. Since deviations cannot be
precluded entirely, we cannot guarantee full agreement. However,
the data in this manual are reviewed regularly and any necessary
corrections included in subsequent editions. Suggestions for
improvement are welcome.
Siemens AG
Automation and Drives
Postfach 48 48, D-90327 Nuernberg
C79000-Z8976-C068-07
© Siemens AG 2001/2002
Technical data subject to change.
Siemens Aktiengesellschaft
Printed in the Federal Republic of Germany
Preface
Preface
Purpose of the Operating Instructions
These Operating Instructions provide you with support during configuration,
commissioning, and troubleshooting of networks with Industrial Ethernet OSMs
(Optical Switch Module) and Industrial Ethernet ESMs (Electrical Switch Module).
The Package
The OSM/ESM includes the following components:
•
OSM/ESM device
•
6-pin plug-in terminal block for connection of the power supply and the signaling
contact
•
One or two 6-pin plug-in terminal blocks for OSMs/ESMs with digital inputs
•
Kit for wall mounting or mounting in 19" cubicle
•
Product information bulletin
•
CD
Installing an OSM/ESM
•
Follow the instructions in Chapter 5 of these operating instructions.
Industrial Ethernet OSM/ESM
C79000-Z8976-C068-07
5
Plik z chomika:
masterkom
Inne pliki z tego folderu:
ET200iS_e.pdf
(22821 KB)
DOC_AS_PL_S7300_HW_moduly.pdf
(7881 KB)
DPPA_E.PDF
(4575 KB)
dyn_funktion_e.pdf
(4571 KB)
Cpu210_e.pdf
(1429 KB)
Inne foldery tego chomika:
Autoryzacja
Kable
Logo
OP Panels
S5
Zgłoś jeśli
naruszono regulamin