hbcom_e.pdf

6,(0(16 Important information,

Contents

Product overview

Installation and uninstallation

SIMATIC

User interface

PROFIBUS-DP

configuration example

COM PROFIBUS

PROFIBUS-FMS

configuration example

Manual

Running PROFIBUS-DP and

PROFIBUS-FMS in parallel

This manual is part of the

COM PROFIBUS CD-ROM

(order no. (66()

Importing configurations

Exporting configurations

Device master files

Assigning shared input

masters

Taking into account other

masters that are not contained

in COM PROFIBUS

Tips and tricks

Glossary, Index

EWA 4NEB 780 6035-02

Edition 1

Safety Guidelines

This manual contains notices which you should observe to ensure your own personal safety, as well as

to protect the product and connected equipment. These notices are highlighted in the manual by a war-

ning triangle and are marked as follows according to the level of danger:

'DQJHU

indicates that death, severe personal injury or substantial property damage ZLOO result if proper pre-

cautions are not taken.

:DUQLQJ

indicates that death, severe personal injury or substantial property damage

result if proper pre-

FDQ

cautions are not taken.

&DXWLRQ

indicates that minor personal injury or property damage can result if proper precautions are not taken.

1RWH

draws your attention to particularly important information on the product, handling the product, or to a

particular part of the documentation.

Qualified Personnel

Only

TXDOLILHGSHUVRQQHO should be allowed to install and work on this equipment. Qualified persons

are defined as persons who are authorized to commission, to ground, and to tag circuits, equipment,

and systems in accordance with established safety practices and standards.

Correct Usage

Note the following :

:DUQLQJ

This device and its components may only be used for the applications described in the catalog or the

technical description, and only in connection with devices or components from other manufacturers

which have been approved or recommended by Siemens.

This product can only function correctly and safely if it is transported, stored, set up, and installed

correctly, and operated and maintained as recommended.

Trademark

SIMATIC®, SIMATIC HMI® and SIMATIC NET® are registered trademarks of SIEMENS AG.

Third parties using for their own purposes any other names in this document which refer to trade-marks

might infringe upon the rights of the trademark owners.

The reproduction, transmission or use of this document or ist

contents is not permitted without express written authority. Offen-

ders will be liable for damages. All rights, including rights created

by patent grant or registration of a utility model or design, are

reserved.

Siemens AG

Automation Group

Industrial Automation Systems

P.O. Box 4848, D-90327 Nuremberg

Disclaimer of Liability

We have checked the contents of this manual for agreement with

the hardware and software described. Since deviations cannot be

pre-cluded entirely, we cannot guarantee full agreement. However,

the data in this manual are reviewed regularly and any necessary

corrections included in subsequent editions. Suggestions for im-

provement are welcomed.

©Siemens AG 1999

Technical data subject to change.

Siemens Aktiengesellschaft

,PSRUWDQWLQIRUPDWLRQ

3XUSRVHRIWKHPDQXDO

The information in this manual tells you how to install COM PROFIBUS and carry

out complete configurations with COM PROFIBUS.

We use two full configuration examples to illustrate how to work with

COM PROFIBUS. These contain all the important functions of COM PROFIBUS

and can be easily followed:

PROFIBUS-DP configuration example

· PROFIBUS-FMS configuration example

7DUJHWDXGLHQFH

This manual is aimed at those who use COM PROFIBUS for planning,

commissioning and diagnostics with PROFIBUS-DP and PROFIBUS-FMS bus

systems based on the EN 50170, Volume 2, PROFIBUS standard.

You will find product-specific configuration information on your PROFIBUS devices

in the product documentation.

6FRSHRIYDOLGLW\

This manual is valid for &20352),%86DVRI9.

It contains a description of the product’s functions that was correct at the time of

going to press. We reserve the right to describe new functions or changes in an

accompanying product information document.

2QOLQHKHOSV\VWHP

All the information you will need is offered in an online help system in

COM PROFIBUS. This contains full descriptions of all the functions of COM

PROFIBUS. In addition, you can also request context-sensitive information on any

open dialog box.

COM PROFIBUS

EWA 4NEB 780 6035-02

iii

Important information

$LGVWRDFFHVVLQJLQIRUPDWLRQ

In order to facilitate rapid access to specific information, the manual contains the

following aids:

A complete table of contents at the beginning of the manual

A glossary after the appendices, in which important technical terms used in the

manual are defined

A thorough index at the end of the manual, which quickly enables you to find

the information you require

)XUWKHUVXSSRUW

If you have any questions of a technical nature, please get in touch with your

contact at the Siemens representative or office assigned to you. You will find the

address in the manuals for the Siemens DP masters - for example, in the "Siemens

Worldwide" appendix of the manual S7-300 Programmable Controller; Hardware

and Installation, in catalogs and on CompuServe (GO AUTFORUM).

If you require device master files, you can obtain them as follows:

By direct modem link on +49 (911) 737972

On the Internet at http://www.ad.siemens.de/csi_e/gsd

&RQVWDQWO\XSGDWHGLQIRUPDWLRQ

You can obtain constantly updated information on SIMATIC products:

On the Internet at http://www.ad.siemens.de/simatic

By calling the fax polling number +49 8765-93 00 50 00

In addition, SIMATIC Customer Support provides you with current information and

downloads that can be of use to you with your SIMATIC products:

On the Internet at http://www.ad.siemens.de/simatic-cs

At the SIMATIC Customer Support Mailbox on +49 (911) 895-7100

To access the mailbox, use a V.34 (28.8 kbps) modem and set the following

parameters: 8, N, 1, ANSI. Alternatively, use ISDN (x.75, 64 kbps).

You can contact SIMATIC Customer Support by phone on +49 (911) 895-7000 and

by fax on +49 (911) 895-7002. You can also send inquiries by e-mail on the

Internet or to the above mailbox.

COM PROFIBUS

EWA 4NEB 780 6035-02

&RQWHQWV

,PSRUWDQWLQIRUPDWLRQ LLL

&RQWHQWV Y

3URGXFWRYHUYLHZ

,QVWDOODWLRQDQGXQLQVWDOODWLRQ

8VHULQWHUIDFH

352),%86'3FRQILJXUDWLRQH[DPSOH

4.1

Starting configuration .............................................................................................. 20

4.2

Setting up the bus configuration ............................................................................. 21

4.3

Entering bus parameters......................................................................................... 22

4.4

Entering master parameters ................................................................................... 24

4.5

Entering host parameters........................................................................................ 26

4.6

Entering slave parameters for the ET 200B............................................................ 27

4.7

Entering slave parameters for the ET 200M ........................................................... 31

4.8

Entering slave parameters for the ET 200S............................................................ 36

4.9

Entering slave parameters for the IM 308-C DP slave ........................................... 42

4.10

Assigning groups..................................................................................................... 46

4.11

Saving the configuration.......................................................................................... 47

4.12

Documenting and printing the configuration ........................................................... 47

4.13

Commissioning the programming device/PC online on the bus ............................. 48

4.14

Transferring (exporting) the configuration to the DP master................................... 49

4.15

Assigning a PROFIBUS address ............................................................................ 51

4.16

Testing the signal states of the individual DP slaves .............................................. 52

4.17

Commissioning the bus configuration ..................................................................... 53

4.18

Evaluating a diagnosis with COM PROFIBUS........................................................ 54

352),%86)06FRQILJXUDWLRQH[DPSOH

5.1

Starting configuration .............................................................................................. 58

5.2

Setting up the bus configuration ............................................................................. 59

5.3

Entering bus parameters......................................................................................... 60

5.4

Entering master parameters ................................................................................... 62

5.5

Entering station parameters for the S7-300 CP 343-5 FMS ................................... 65

COM PROFIBUS

EWA 4NEB 780 6035-02

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: