DPASI_e.pdf

(903 KB) Pobierz
Preface, Contents
1
Overview
2
ASi Basics
SIMATIC
3
Configuration Options
Distributed I/O System
DP/ASi Link
4
Installing and Wiring DP/ASi Link
5
Configuring the DP/ASi Link
6
Manual
DP/ASi Link to S7
7
Operating Modes
8
Diagnostics and Error Handling
Appendices
A
Technical Data
B
I/O Code
C
Parameterization Message
D
Configuration Message
Glossary, Index
EWA 4NEB 710 6055-02b
Edition 3
921909455.045.png 921909455.046.png 921909455.047.png 921909455.048.png 921909455.001.png 921909455.002.png 921909455.003.png 921909455.004.png 921909455.005.png 921909455.006.png 921909455.007.png 921909455.008.png 921909455.009.png 921909455.010.png 921909455.011.png 921909455.012.png 921909455.013.png 921909455.014.png 921909455.015.png 921909455.016.png
 
Safety Guidelines
This manual contains notices which you should observe to ensure your own personal safety, as
well as to protect the product and connected equipment. These notices are highlighted in the
manual by a warning triangle and are marked as follows according to the level of danger:
Danger
!
indicates that death, severe personal injury or substantial property damage will result if proper
precautions are not taken.
Warning
indicates that death, severe personal injury or substantial property damage can result if proper
precautions are not taken.
!
Caution
!
indicates that minor personal injury or property damage can result if proper precautions are not taken.
Note
draws your attention to particularly important information on the product, handling the product, or
to a particular part of the documentation.
Qualified Personnel
The device/system may only be set up and operated in conjunction with this manual.
Only qualified personnel should be allowed to install and work on this equipment. Qualified
persons are defined as persons who are authorized to commission, to ground, and to tag circuits,
equipment, and systems in accordance with established safety practices and standards.
Correct Usage
Note the following:
Warning
This device and its components may only be used for the applications described in the catalog or the
technical description, and only in connection with devices or components from other manufacturers
which have been approved or recommended by Siemens.
This product can only function correctly and safely if it is transported, stored, set up, and installed
correctly, and operated and maintained as recommended.
!
Trademarks
SIMATIC and SIMATIC NET are registered trademarks of SIEMENS AG.
Some of the other designations used in these documents are also registered trademarks; the own-
er’s rights may be violated if they are used be third parties for their own purposes.
Copyright Siemens AG 1995 All rights reserved
The reproduction, transmission or use of this document or its
contents is not permitted without express written authority.
Offenders will be liable for damages. All rights, including rights
created by patent grant or registration of a utility model or design, are
reserved.
Siemens AG
Automation Group
Industrial Automation Systems
P.O. Box 4848, D-90327 Nuremberg
Disclaimer of Liability
We have checked the contents of this manual for agreement with the
hardware and software described. Since deviations cannot be pre-
cluded entirely, we cannot guarantee full agreement. However, the
data in this manual are reviewed regularly and any necessary cor-
rections included in subsequent editions. Suggestions for improve-
ment are welcomed.
Technical data subject to change.
Siemens AG 1995
Siemens Aktiengesellschaft
Order No. 6ES7 156-0AA00-8BA0
Distributed I/O System DP/ASi Link
EWA 4NEB 710 6055 02b
ii
921909455.017.png 921909455.018.png 921909455.019.png 921909455.020.png 921909455.021.png 921909455.022.png 921909455.023.png 921909455.024.png 921909455.025.png 921909455.026.png 921909455.027.png 921909455.028.png 921909455.029.png 921909455.030.png 921909455.031.png 921909455.032.png 921909455.033.png 921909455.034.png
 
Preface
Purpose of manual
The information contained in this manual will enable you to:
install an Actuator Sensor Interface (ASi)
commission the DP/ASi link
Manual contents
The scope of delivery of MLFB 6ES7 156-0AA00-8AA0 consists of the
manual:
Distributed I/O System
DP/ASi Link, Edition 3
installing and wiring the distributed I/O system DP/ASi link
configuring the DP/ASi link
diagnostics and error handling
technical data
Applicability
The present manual is valid for:
Order No.
DP/ASi Link
Release (or Later)
DP/ASi Link
Manual
Edition
6ES7 156-0AA00-0XA0
03
03
03
6ES7 156-0AA01-0XA0
01
The present manual contains a description of all the functions incorporated in
the DP/ASi link at the time this manual was published. We reserve the right
to describe modified functions in a Product Information.
Distributed I/O System DP/ASi Link
EWA 4NEB 710 6055-02b
iii
921909455.035.png 921909455.036.png 921909455.037.png 921909455.038.png 921909455.039.png 921909455.040.png 921909455.041.png 921909455.042.png
Preface
Changes from
previous edition
Compared to the previous edition of this manual, Distributed I/O System DP/
ASi Link having the Order No. 6ES7 156-0AA00-8AA0, Edition 2, the fol-
lowing changes have been incorporated:
DP/ASi link to S7
diagnostics during operation with an S7/M7 DP master
Standards and
approvals
The DP/ASi link meets the requirements and criteria of the following stan-
dards and approvals:
IEC 1131, Part 2
EN 50170 Volume 2, PROFIBUS
ASi: Actuator Sensor Interface Complete Specification
CE mark requirements
CSA, UL and FM approvals
You will find complete details of approvals and standards in appendix A.1.
How this manual
fits in
This manual, DP/ASi Link , describes the DP/ASi link and the installation of
the ASi.
The description of the PROFIBUS-DP and a master interface such as
IM 308-C do not form a part of this manual. You will find further information
on these subjects in the manual called Distributed I/O System ET 200 , Order
No. 6ES5 998-3ES12.
CD-ROM
The Distributed I/O System DP/ASi Link can be acquired on a CD-ROM as
an electronic manual.
Aids to accessing
the manual
You can quickly access specific information in the manual using the follow-
ing access aids:
At the beginning of the manual, you will find a complete list of manual
contents and lists of illustrations and tables contained in the whole docu-
ment.
Within the chapters, you will find information in the left-hand margin
giving you an overview of the subject that is dealt with.
Following the appendices, there is a glossary in which technical terms
used in the manual are defined.
At the end of the manual, you will find a comprehensive index enabling
rapid access to the information you require.
Distributed I/O System DP/ASi Link
EWA 4NEB 710 6055-02b
iv
921909455.043.png
Preface
Further support
Should you have any technical queries, please contact your Siemens repre-
sentative at the agents or branch office responsible. You will find the address
in the manuals describing the DP masters – for example, in the appendix
“Siemens Worldwide” to the S7-300 Programmable Controller; Hardware
and Installation manual, in catalogs and on CompuServe ( GO AUTFORUM ).
In addition, you can contact our hotline by calling +49 (911) 895-7000 (Fax
7001).
Should you require the type file or the GSD file, you can download them
over your modem by dialing +49 (911) 737972.
In the event of queries or remarks concerning the manual itself, please com-
plete the Remarks Form at the end of the manual and return it to the address
specified. We would kindly ask you to enter your own personal assessment of
the manual on the Remarks Form.
To help you get started with the distributed I/O system ET 200, we hold a
”KO-ET 200” workshop. If you are interested in attending the workshop,
please contact your next area training center or the principal training center
in Nuremberg, Germany, by dialing +49 911 895 3154.
Distributed I/O System DP/ASi Link
EWA 4NEB 710 6055-02b
v
921909455.044.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin