Bench - Entryway Storage Bench Plans.pdf - Projekty - stolarstwo - QSR

Free Entryway Storage Bench Plans - How To Build An Entryway Stora...

http://www.wayneofthewoods.com/deacon%20bench.html

Free Entryway Storage Bench Plans

How To Build An Entryway Storage Bench

Tools | Building Plans | Wood Finishing | Hardware

[an error occurred while processing this directive]

Free Storage Deacon Bench Plan

Check Out The Building Plans Below!

Build the wood Entryway Storage Boot Bench shown on the right with just a few tools

and a small investment in materials! It can also be used as a Bedroom Storage Bench or

as a Blanket Chest...even a Hope Chest!

Click on image for

larger view

Rod's Woodworking Corner

Building an Entryway Storage Bench that can also be used in an entry way, a mud room, or even as a Bedroom

Storage Bench can be fun and practical. This simple, butt-jointed Blanket Chest can hold blankets or a good

number of gloves, hats, scarves, etc. You can build this wood storage bench from one, 3/4" x 4' x 8' plywood

panel plus a few other necessities.

Material List:

Note: For Outdoor use, use only cedar or treated lumber.

One piece of 3/4" hardwood plywood, 4' x 8', plus matching edging material.

One piece of 1/2" x 2' x 4' plywood for the bottom panel.

One piece of 1 x 3 x 48" hardwood for the top Cross piece.

1 5/8" Woodscrews.

A set of Hinges, one, interior lid support, wood plugs and/or wood filler.

1 of 9

05/05/2007 2:18 PM

Free Entryway Storage Bench Plans - How To Build An Entryway Stora...

http://www.wayneofthewoods.com/deacon%20bench.html

2 of 9

05/05/2007 2:18 PM

Free Entryway Storage Bench Plans - How To Build An Entryway Stora...

http://www.wayneofthewoods.com/deacon%20bench.html

Step 1, Cut the Blanket Chest Pieces - A. Select 3/4" x 48" x 96" plywood panel; using your Table Saw with

Extension Wings or using your Circular Saw Cutting Guide , crosscut the panel to 36 3/4". Using your table saw,

rip it to two pieces @ 14" for the Front and Back Base Panels.

B. Select 3/4" plywood panel; crosscut the panel to 15"; rip it to two pieces @ 17".

3 of 9

05/05/2007 2:18 PM

Free Entryway Storage Bench Plans - How To Build An Entryway Stora...

http://www.wayneofthewoods.com/deacon%20bench.html

Northern Tool Free Shipping on orders $150 or more

C. Select the Left/Right side panels; Set the dado blades to 3/4" wide by 1/8" deep; set the fence to 1/2"; at each

of the four edges beginning at the top edge, make the four passes 14" down as shown above to receive the Front

and Back Panels.

D. Select the two side panels; set your router with a 1/2" straight gouge bit; set it for 1/4" deep cut; set the guide

so the top edge of the cut is 13" down from the top edge; Make the router pass as indicated by the blue lines

above to receive the Bottom Panel.

E. Select the Front and Back Panels and your router already set with the 1/2" bit and 1/4" depth, measure down

the same 13" and router the bottom edge as shown above.

4 of 9

05/05/2007 2:18 PM

Free Entryway Storage Bench Plans - How To Build An Entryway Stora...

http://www.wayneofthewoods.com/deacon%20bench.html

F. Select the 1/2" x 24" x 48" plywood; crosscut this bottom panel to 37 1/4"; rip this panel to 13 1/8".

G. Dry fit the base pieces.

5 of 9

05/05/2007 2:18 PM

Bench - Entryway Storage Bench Plans.pdf

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: