customer pay mmi system 2008.pdf

Customer pay – MMI System Update

Facts:

•

Update to MY2008 MMI System Software with Update CD 4L0 906 961 H

•

A Software Version Management (SVM-) Update is required after the MMI System Update – VAS Tester with

online connection required

•

The engine must run or a battery charger/maintainer must be connected to the battery during the MMI System

Update.

•

In case of a component breakdown during update programming (communication can’t be established, even

after hardware resets), replace the affected module and claimed it as a W2 claim.

•

The following features will be available:

Cell phone

compatibility

upgrade

Disclaimer

screen

during

start.

French

in voice

recogni-

tion

possible

Navigation

commands

mute

during

phone call

Navigation:

Altitude

visible in

MMI

display

USB -

compatibility

with AMI (if

applicable)

A8 MY 04-05

A6 MY05

A8 MY 06

A6 MY 06

Audi Q7 MY07

A8 MY2007

A6 MY2007

Restrictions:

A8 MY2004 : JF campaign (MMI update to Zug 317) had to be performed.

A8 MY2004/05 and A6 MY2005 with Navigation require at least Navigation DVD Version 5 .

If an older Version (1 or 4) is installed, the customer must purchase the package

MMI System Update + Navigation DVD Version 2007.

If Version 5, 6, 2007 is installed, the vehicle only requires an MMI System Update.

In case the MMI system of the customer’s vehicle was updated in a prior dealership visit, an MMI system update is

not necessary. Inform the customer without charging him.

An interim update to Zug 730 (MY2007 MMI, Update CD 4F0 906 961AB) is mandatory in case the current

Zug is < 730 ( = MY04-06 vehicles, which were not updated in the past)

Update procedure

Verification, if an MMI system update is necessary

Press and hold the SETUP button, then additionally the RETURN button of the MMI controller E380 until

the MMI display changes to the red screen.

Select Interfacebox (0x0100) and verify the SW-Index

(NOTE: This is an example for software 2740)

If the SW-Index is 4140 , an update is not required . The vehicle has the latest version and the customer

must not be charged. Reason might be a prior update to the latest Zug software.

If the SW-Index is 3360 , just the MY 2008 MMI Update (4L0 906 961 H) has to be performed.

If the SW-Index is between 0600 and 2750 , two MMI System update have to be performed:

First with Update CD 4F0 906 961AB and afterwards with Update CD 4L0 906 961 H. The update

procedure is the same.

If the SW-Index is 0150, please contact the Audi helpline.

In case of a MY2004/2005 vehicle : Verify that the Navigation DVD is at least of Version 5 .

If the Navigation DVD is Version 4, the customer must purchase the MMI System Update + Navigation DVD

Version 2007 - package.

Update procedure

Connect a battery charger/maintainer to the appropriate studs in the vehicle.

Write down the following Adaptation values in 07 – Display/Control unit for subsequent verification

1, 2, 3, 4, 11, 12, 16

Install the MMI Update CD in the first slot of the CD changer.

Note: Eject potentially installed CD’s beforehand!

Press and hold the SETUP button, then additionally the RETURN button of the MMI controller E380 until

the MMI display changes to the red screen.

5. Select SWUpdate with the lower right soft key and navigate with the Main knob through the menus to the

Start download option

Select CD-ROM

Select Standard

Scroll down to Start download

Select Start download

Obey the displayed warning, scroll down …

… and accept the Run download? - request.

Note: The SW Update can take up to 80 minutes and usually runs

automatically. However check the progress every 20 minutes.

After the Update press Restart MMI

In some cases not all MMI components are updated in the first update.

To ensure that all components are updated, repeat the update procedure, until the following

message is displayed after accepting the Run download? request.

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: