eagle_koh.pdf

(99 KB) Pobierz
Eagle.PDF
Eagle
Ronald Koh - 1988
1.
Use a thin sheet of paper or
tissue foil of at least 15 cm
square.
2.
Fold diagonally in half from left to right,
crease well, and unfold. Repeat by folding
in half from top to bottom, and unfold.
Valley fold the lower diagonal edges to the
crease line in the centre and turn paper over.
3.
4.
Open out to the sides, effectively
unfolding Step 2.
5.
Fold down the triangular
section at the top and turn
paper over.
6.
Make two diagonal folds as illustrated, in line
with the edge of the triangular layer underneath.
Crease firmly, and unfold.
Lift up the triangular piece from behind.
c
6148081.051.png 6148081.052.png 6148081.053.png 6148081.054.png 6148081.001.png 6148081.002.png 6148081.003.png 6148081.004.png 6148081.005.png 6148081.006.png 6148081.007.png
7.
8.
Repeat from Step 2 on the lower half of the
paper, then turn the paper over.
Valley fold through the circled intersecting
crease lines, crease firmly, and unfold.
9.
10.
... like so. Now fold the diagonal edge in the
middle to the vertical crease in the centre,
crease firmly, and unfold. Repeat on the
other side.
11.
Collapse the paper along the illustrated
mountain and valley folds ...
12.
Pull the flaps on each side slightly apart and
sink fold. You may need to stick a finger
through the underside to guide the sink fold
precisely along the crease lines made in Step
10. Repeat on the other side.
Flatten the rest of the model to the position
at Step 10.
6148081.008.png 6148081.009.png
13.
14.
Separate the two diagonal edges on the
right and squash fold. Repeat behind.
Fold the bottom corner to
the top, crease well, and
unfold.
15.
16.
17.
Separate the two diagonal
edges and squash fold
again.
Fold and unfold, creasing
firmly ...
... then petal fold.
18.
19.
20.
Fold the triangular flap
down ...
... then fold the flap on the
left to the right. Repeat
from Step 15 on the next
flap on the left.
Grasp the circled point
and gradually pull the flap
upwards as far as it can
go, opening out and
flattening the layers
beneath ...
21.
22.
... like this, before bringing
down the flap again.
The model should now look
like this. Turn the model over.
6148081.010.png 6148081.011.png 6148081.012.png 6148081.013.png 6148081.014.png 6148081.015.png 6148081.016.png 6148081.017.png 6148081.018.png
23.
24.
25.
Repeat Step 15 on the
right, and then on the left.
Mountain fold the triangular
portion of the uppermost
layer under and against
itself.
Fold the first flap on the
right to the left.
26.
27.
28.
Fold and unfold, creasing
firmly ...
... then reverse fold.
Fold and unfold again,
from the left corner to the
corner on the right.
29.
30.
31.
Now mountain fold the
excess paper under as
well ...
... then close up with a
rabbit's ear fold.
Fold the flap on the left
to the right and repeat
from Step 26 on the
other side.
32.
33.
34.
Bring the corners from
the sides to the apex.
Squash fold ...
... and then petal fold,
as you did in
Steps 16 to 18.
6148081.019.png 6148081.020.png 6148081.021.png 6148081.022.png 6148081.023.png 6148081.024.png 6148081.025.png 6148081.026.png 6148081.027.png 6148081.028.png 6148081.029.png 6148081.030.png 6148081.031.png 6148081.032.png 6148081.033.png 6148081.034.png 6148081.035.png 6148081.036.png 6148081.037.png
35.
36.
37.
Grasp the flaps at the
circled area and pull
gently apart, ...
... then reverse fold to hide
the triangular tab
beneath.
Turn model
over.
38.
39.
40.
Swivel both layers to
the left, ...
... grasp the paper at the
circled area and make a
crimp fold while drawing
the paper, slightly beyond
midway, towards the top ...
... like this. Return the two
layers folded in Step 38 to
the right and flatten out.
41.
42.
43.
The model should now look
like this. Repeat Steps 38 to
40 on the left side of the
model.
The pieces on each side,
which will form the wings,
should be symetrical. Reverse
fold each of the tabs on the
sides ...
... then valley fold the sides of
the top layer to narrow.
44.
45.
46.
Valley fold the tail piece
upwards, crease firmly, and
unfold. Next crimp fold the
layer at the base of each wing
as illustrated, then turn model
over.
Mountain fold the first layer at
the bottom corner of the wings
within itself, then separate and
draw the central vertical edges
of the tailpiece to the sides ...
... and reverse fold to hide the
lower portion of the tailpiece
within the opening ...
6148081.038.png 6148081.039.png 6148081.040.png 6148081.041.png 6148081.042.png 6148081.043.png 6148081.044.png 6148081.045.png 6148081.046.png 6148081.047.png 6148081.048.png 6148081.049.png 6148081.050.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin